2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1412 Ambient Temperature Sensor Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The cooler thermistor (ambient temperature sensor) is installed in the front part of the cooler condenser assembly. This sensor is connected to the air conditioning amplifier assembly and detects fluctuations in the ambient temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the cooler thermistor (ambient temperature sensor) changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies a voltage (5 V) to the cooler thermistor (ambient temperature sensor) and reads voltage changes as changes in the resistance of the cooler thermistor (ambient temperature sensor).
DTC Code
DTC Detection Condition
Trouble Area
B1412
An open or short in the cooler thermistor (ambient temperature sensor) circuit is detected for 8.5 minutes or more.
  1. Cooler thermistor (ambient temperature sensor)
  2. Harness or connector
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E193111E23

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (AMBIENT TEMP SENSOR)
  1. Use the Data List to check if the cooler thermistor (ambient temperature sensor) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambient Temp Sensor
    Cooler thermistor (ambient temperature sensor) /
    Min: -23.3°C (-9.94°F)
    Max: 65.95°C (150.71°F)
    Actual ambient temperature displayed
    Open in the circuit: -23.3°C (-9.94°F).
    Short in the circuit: 65.95°C (150.71°F).

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)

  1. E184843E02
    Remove the cooler thermistor (ambient temperature sensor) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    10°C (50°F)
    3.00 to 3.73 kΩ
    15°C (59°F)
    2.45 to 2.88 kΩ
    20°C (68°F)
    1.95 to 2.30 kΩ
    25°C (77°F)
    1.60 to 1.80 kΩ
    30°C (86°F)
    1.28 to 1.47 kΩ
    35°C (95°F)
    1.00 to 1.22 kΩ
    40°C (104°F)
    0.80 to 1.00 kΩ
    45°C (113°F)
    0.65 to 0.85 kΩ
    50°C (122°F)
    0.50 to 0.70 kΩ
    55°C (131°F)
    0.44 to 0.60 kΩ
    60°C (140°F)
    0.36 to 0.50 kΩ

    Text in Illustration 
    *a
    Sensing Portion
    *b
    Resistance
    *c
    Allowable Range
    *d
    Temperature

    NOTICE:
    1. Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.
    2. When measuring, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (refer to the graph).



NG
REPLACE COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the A14 cooler thermistor (ambient temperature sensor) connector.

  1. Disconnect the E81 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A14-1 - E81-5 (TAM)
    Always
    Below 1 Ω
    A14-2 - E81-13 (SG-2)
    E81-5 (TAM) - Body ground
    Always
    10 kΩ or higher
    E81-13 (SG-2) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← B1412 Ambient Temperature Sensor Circuit (Sep 2011 – Dec 2011)B1413 Evaporator Temperature Sensor Circuit (Sep 2011 – Dec 2011) →