B1446 Air Mix Damper Control Servo Motor Circuit (Driver Side)
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix damper to any position. As a result, the air mix damper varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air is as requested.- HINT:
- Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1446 |
The air mix damper position does not change for 30 seconds or more when the air conditioning amplifier assembly operates the No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (AIR MIX SERVO TARG PULSE [D]) |
Use the Data List to check if the No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) is functioning properly (Click here).
Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Mix Servo Targ Pulse (D)
No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) target pulse / Min.: 0, Max.: 255
for LHD- MAX. COOL: 90 (pulse)
- MAX. HOT: 8 (pulse)
for RHD- MAX. COOL: 8 (pulse)
- MAX. HOT: 90 (pulse)
-
- OK:
- The display is as specified in the normal condition column.
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table)
A
OK (When troubleshooting according to the DTC)
B
NG
C
- MAX. COOL: 90 (pulse)
|
|
||||
|
|
||||
| A | ||
| ||
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIR MIX SERVO TARG PULSE [D]) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) operates (Click here).
Air Conditioner Tester Display
Test Part
Control Range
Diagnostic Note
Air Mix Servo Targ Pulse (D)
No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo)
Min.: 0, Max.: 255
-
- OK:
- The No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) pulse signal changes according to the target pulse specified by the Active Test.
|
|
||||
| OK | ||
| ||
| 3. REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX DAMPER SERVO) |
Temporarily replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo).
- for LHD: Click here.
- for RHD: Click here.
- HINT:
- Since the No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) cannot be inspected while it is removed from the vehicle, replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) with a new or normally functioning one.
- for LHD: Click here.
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1446 is not output
A
DTC B1446 is output
B
|
|
||||
| A | ||
| ||
| 4. REPLACE AIR CONDITIONING HARNESS ASSEMBLY |
Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one.
- for LHD: Click here.
- for RHD: Click here.
- for LHD: Click here.
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1446 is not output
A
DTC B1446 is output
B
|
|
||||
| A | ||
| ||
