2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1442 Air Inlet Damper Control Servo Motor Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The No. 1 blower damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet damper to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1442
The air inlet damper position does not change for 30 seconds or more when the air conditioning amplifier assembly operates the No. 1 blower damper servo sub-assembly.
  1. No. 1 blower damper servo sub-assembly
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E180810E76

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (AIR INLET DAMPER TARG PULSE)
  1. Use the Data List to check if the No. 1 blower damper servo sub-assembly is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Inlet Damper Targ Pulse
    No. 1 blower damper servo sub-assembly target pulse / Min.: 0, Max.: 255
    for LHD
    1. Recirculation: 37 (pulse)
    2. Fresh: 9 (pulse)
    for RHD
    1. Recirculation: 9 (pulse)
    2. Fresh: 37 (pulse)
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIR INLET DAMPER TARG PULSE)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the No. 1 blower damper servo sub-assembly operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Inlet Damper Targ Pulse
    No. 1 blower damper servo sub-assembly
    Min.: 0, Max.: 255
    -

    OK:
    The No. 1 blower damper servo sub-assembly pulse signal changes according to the target pulse specified by the Active Test.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

3. REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY
  1. Temporarily replace the No. 1 blower damper servo sub-assembly (Click here).

    HINT:
    Since the No. 1 blower damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the No. 1 blower damper servo sub-assembly with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1442 is not output
    A
    DTC B1442 is output
    B



B
Go to step 4
A

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

4. REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Temporarily replace the air conditioning harness assembly with a new or normally functioning one.

    1. for LHD: Click here.
    2. for RHD: Click here.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1442 is not output
    A
    DTC B1442 is output
    B



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)


← B1423 Pressure Sensor Circuit (from Jan 2012)B1442 Air Inlet Damper Control Servo Motor Circuit (from Jan 2012) →