2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Sep 2011


PERFORM SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is output, perform troubleshooting procedures for that DTC.

  1. Check if sparks occur.

    1. Remove the ignition coils and spark plugs (Click here).

    2. Install the spark plug to the ignition coil and connect the ignition coil connector.

    3. Disconnect the 8 injector connectors.

    4. Ground the spark plug.

    5. Visually check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Be sure to ground the spark plug when checking.
      2. If the ignition coil has been struck or dropped, replace it.
      3. Do not crank the engine for more than 2 seconds.

  1. Check that the wire harness side connector of the ignition coil with igniter is securely connected.

    Result 
    Result
    Proceed to
    NG
    Connect securely
    OK
    Go to next step

  1. Perform a spark test on each ignition coil with igniter.

    1. If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.

    2. Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.

      Result 
      Result
      Proceed to
      OK
      Replace ignition coil with igniter
      NG
      Go to next step

  1. Check spark plug.

    Result 
    Result
    Proceed to
    NG
    Replace spark plug
    OK
    Go to next step

  1. Check the power supply to the ignition coil with igniter.

    1. Turn the engine switch on (IG).

    2. Check that there is battery voltage at the ignition coil positive (+) terminal.

      Result 
      Result
      Proceed to
      NG
      Check wiring between engine switch and ignition coil with igniter
      OK
      Go to next step

  1. Check the VVT sensor for intake side (Click here).

  1. Check the VVT sensor for exhaust side (Click here).

  1. Check the camshaft position sensor (Click here).

  1. Check the crankshaft position sensor (Click here).

  1. Check the IGT signal circuit (Click here).

  1. Connect the 8 injector connectors.

  1. Install the ignition coils and spark plugs (Click here).


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.

  1. Check the electrode.

    1. A110413E09
      Using a megohmmeter, measure the insulation resistance.

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark plug (terminal part) - Body ground
      Always
      10 MΩ or higher

      Text in Illustration 
      *1
      Ground
      If the insulation resistance is below the specified range, replace the spark plug.

      HINT:
      If a megohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. B062019E01
    Check the spark plug for any damage to its threads and insulator.
    If there is any damage, replace the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Type
    DENSO made
    SK20HR11

    HINT:
    Maximum electrode gap for a used spark plug: 1.3 mm (0.0512 in.).
    If the gap is more than the maximum, replace the spark plug.
    Electrode gap for a new spark plug: 1.0 to 1.1 mm (0.0394 to 0.0433 in.).

    NOTICE:
    If adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.

    If the electrode has traces of wet carbon, allow it to dry and then clean it with a spark plug cleaner.

    Standard air pressure:
    588 kPa (6.0 kgf/cm2, 85 psi)

    Standard duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

← SYSTEM DIAGRAM (from Sep 2011)COMPONENTS (from Sep 2011) →