ON-VEHICLE INSPECTION
Inspection · Vehicles built from Jan 2012
| PERFORM SPARK TEST |
Check for DTCs (Click here).
- NOTICE:
- If any DTC is output, perform troubleshooting procedures for that DTC.
Check if sparks occur.
Remove the ignition coils and spark plugs (Click here).
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the 8 injector connectors.
Ground the spark plug.
Visually check that sparks occur while the engine is being cranked.
- NOTICE:
- When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.
- Do not crank the engine for more than 2 seconds.
For vehicles with a cranking hold function, turn the engine switch off during cranking to stop cranking.
- If an ignition coil assembly is struck or dropped, replace it with a new one.
- If a spark plug is struck or dropped, replace it with a new one.
- When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.
If sparks do not occur normally in 1 or more cylinders, perform the "Ignition Coil and Spark Test" below.
| INSPECT IGNITION COIL AND SPARK PLUG |
Spark test flowchart.
Check that the wire harness side connector of the ignition coil is securely connected.
Result Result
Proceed to
NG
Connect securely
OK
Go to next step
Perform a spark test on each ignition coil.
- If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.
- Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.
Result Result
Proceed to
OK
Replace ignition coil
NG
Go to next step
- If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.
Check the power supply to the ignition coil.
- Turn the engine switch on (IG).
- Check that there is battery voltage at the ignition coil positive (+) terminal.
Result Result
Proceed to
NG
Check wiring between battery and ignition coil
OK
Go to next step
- Turn the engine switch on (IG).
Inspect the spark plug.
- Replace the spark plug with a normal one.
- Perform a spark test.
Result Result
Proceed to
OK
Replace spark plug
NG
Inspect the ignition system (Click here)
- NOTICE:
- If an ignition coil assembly is struck or dropped, replace it with a new one.
- If a spark plug is struck or dropped, replace it with a new one.
- If an ignition coil assembly is struck or dropped, replace it with a new one.
- Replace the spark plug with a normal one.
Connect the 8 injector connectors.
Install the ignition coils and spark plugs (Click here).
| INSPECT SPARK PLUG |
- NOTICE:
- Do not use a wire brush for cleaning.
- Do not attempt to adjust the electrode gap of a used spark plug.
- Do not use a wire brush for cleaning.
Check the electrode.
Using a megohmmeter, measure the insulation resistance.

- Standard Insulation Resistance:
Tester Connection
Condition
Specified Condition
Spark plug (terminal part) - Body ground
Always
10 MΩ or higher
If the result is not as specified, replace the spark plug.Text in Illustration *1
Ground
- HINT:
- If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:
Start the engine.*
Quickly accelerate the engine to 4000 rpm 5 times.*
- NOTICE:
- *: Do not perform this step if P0300 (misfire detection) or a related DTC is stored.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is any damage, replace the spark plug.- Recommended Spark Plug:
Manufacturer
Type
DENSO
SK20HR11
Check the spark plug electrode gap.

- Maximum electrode gap for a used spark plug:
- 1.3 mm (0.0512 in.)
- Electrode gap for a new spark plug:
- 1.0 to 1.1 mm (0.0394 to 0.0433 in.)
- NOTICE:
- If adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.
- Standard air pressure:
- 588 kPa (6.0 kgf/cm2, 85 psi)
- Standard duration:
- 20 seconds or less
- HINT:
- Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
