2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Microphone Circuit between Microphone and Radio Receiver

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

  1. The multi-media module receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
  2. Using this circuit, the multi-media module receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the multi-media module receiver assembly.

WIRING DIAGRAM

E248564E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Disconnect the R7 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-49 (SNS2) - R7-20 (SNS2)
    Always
    Below 1 Ω
    F77-29 (MACC) - R7-25 (ACC)
    Always
    Below 1 Ω
    F77-27 (MIN+) - R7-27 (MI1+)
    Always
    Below 1 Ω
    F77-48 (MIN-) - R7-26 (MIC-)
    Always
    Below 1 Ω
    F77-49 (SNS2) - Body ground
    Always
    10 kΩ or higher
    F77-29 (MACC) - Body ground
    Always
    10 kΩ or higher
    F77-27 (MIN+) - Body ground
    Always
    10 kΩ or higher
    F77-48 (MIN-) - Body ground
    Always
    10 kΩ or higher
    F77-28 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

  1. E239014E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-28 (SGND) - Body ground
    Always
    Below 1 Ω
    F77-48 (MIN-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F77-29 (MACC) - Body ground
    Engine switch on (ACC)
    4 to 6 V

Text in Illustration 
*a
Component with harness connected
(Multi-media Module Receiver Assembly)


NG
MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


Go to step 5

3. INSPECT MAP LIGHT ASSEMBLY

  1. E248565E01
    Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    26 (MIC-) - 20 (SNS2)
    Always
    Below 1 Ω



NG
Go to step 5
OK


4. CHECK MAP LIGHT ASSEMBLY
E248566E01
  1. Turn the engine switch on (ACC).

  1. Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Text in Illustration 
    *a
    Component with harness connected
    (Map Light Assembly)
    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is not output.
    A
    A waveform synchronized with the voice input to the map light assembly is output.
    B



B
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

5. CHECK TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a new or normally functioning one (Click here).

  1. Check if the same malfunction recurs.

    Result 
    Result
    Proceed to
    Malfunction does not recur
    (returns to normal).
    A
    Malfunction recurs.
    B



B
REPLACE MAP LIGHT ASSEMBLY (Click here)
A

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)


← Display Signal Circuit between Multi-display and Radio Receiver (from Jan 2012)PARTS LOCATION (Sep 2011 – Dec 2011) →