2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Power Mirrors do not Return to Memorized Position

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

SYSTEM DESCRIPTION

When the seat memory switch 1, seat memory switch 2 or seat memory switch 3 is pressed, the position control ECU and switch mirror position signal is sent through the CAN communication line to the outer mirror control ECU. The outer mirror control ECU then activates the mirror control motors to move the mirrors to the previously recorded positions.

WIRING DIAGRAM

B188313E03

INSPECTION PROCEDURE


1. CHECK DTC
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output (for LHD)
    B
    CAN DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK POWER MIRROR CONTROL FUNCTION
  1. Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

    OK:
    Mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.



NG
PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY)
  1. Check the Data List for proper functioning of the mirror position memory (Click here).

    Mirror 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Mirror Memory No.1
    Mirror position memorized in seat memory switch memory1 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No.2
    Mirror position memorized in seat memory switch memory2 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No.3
    Mirror position memorized in seat memory switch memory3 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


4. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)
  1. Check the Data List for proper functioning of the mirror position sensor (Click here).

    Mirror 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    RH Mir Position Sensor V
    RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    RH Mir Position Sensor H
    RH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    LH Mir Position Sensor V
    LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    LH Mir Position Sensor H
    LH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -

    OK:
    When mirror control switch is operated, voltage changes within range shown in above chart.

    Result 
    Result
    Proceed to
    LH side mirror does not operate normally
    A
    RH side mirror does not operate normally
    B
    Mirror operates normally
    C



B
Go to step 7

C
GO TO FRONT POWER SEAT CONTROL SYSTEM (Click here)
A


5. CHECK OUTER MIRROR CONTROL ECU
B187976E54
  1. for LHD:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I18-2 (LVC) - I18-3 (LE1)
      Engine switch on (IG)
      4.7 to 5.5 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I18-3 (LE1) - Body ground
      Always
      Below 1 Ω

  1. for RHD:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I24-2 (LVC) - I24-3 (LE1)
      Engine switch on (IG)
      4.7 to 5.5 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I24-3 (LE1) - Body ground
      Always
      Below 1 Ω



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)

  1. B315278E01
    for LHD:
    1. Disconnect the I18 ECU connector.

    2. Disconnect the I35 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I18-2 (LVC) - I35-10 (VC)
      Always
      Below 1 Ω
      I18-3 (LE1) - I35-21 (E1)
      I18-4 (VSR) - I35-22 (VSRL)
      I18-5 (HSRL) - I35-11 (HSRL)
      I35-10 (VC) - Body ground
      Always
      10 kΩ or higher
      I35-21 (E1) - Body ground
      I35-22 (VSRL) - Body ground
      I35-11 (HSRL) - Body ground

  1. for RHD:

    1. Disconnect the I24 ECU connector.

    2. Disconnect the I35 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I24-2 (LVC) - I35-10 (VC)
      Always
      Below 1 Ω
      I24-3 (LE1) - I35-21 (E1)
      I24-4 (VSR) - I35-22 (VSRL)
      I24-5 (HSRL) - I35-11 (HSRL)
      I35-10 (VC) - Body ground
      Always
      10 kΩ or higher
      I35-21 (E1) - Body ground
      I35-22 (VSRL) - Body ground
      I35-11 (HSRL) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (Click here)

7. CHECK OUTER MIRROR CONTROL ECU
B187976E55
  1. for LHD:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I18-22 (RVC) - I18-23 (RE1)
      Engine switch on (IG)
      4.7 to 5.5 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I18-23 (RE1) - Body ground
      Always
      Below 1 Ω

  1. for RHD:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I24-22 (RVC) - I24-23 (RE1)
      Engine switch on (IG)
      4.7 to 5.5 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I24-23 (RE1) - Body ground
      Always
      Below 1 Ω



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)

  1. B315278E05
    for LHD:
    1. Disconnect the I18 ECU connector.

    2. Disconnect the I32 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I18-22 (RVC) - I32-10 (VC)
      Always
      Below 1 Ω
      I18-23 (RE1) - I32-21 (E1)
      I18-24 (VSRR) - I32-22 (VSSR)
      I18-25 (HSRR) - I32-11 (HSSR)
      I32-10 (VC) - Body ground
      Always
      10 kΩ or higher
      I32-21 (E1) - Body ground
      I32-22 (VSSR) - Body ground
      I32-11 (HSSR) - Body ground

  1. for RHD:

    1. Disconnect the I24 ECU connector.

    2. Disconnect the I32 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I24-22 (RVC) - I32-10 (VC)
      Always
      Below 1 Ω
      I24-23 (RE1) - I32-21 (E1)
      I24-24 (VSRR) - I32-22 (VSSR)
      I24-25 (HSRR) - I32-11 (HSSR)
      I32-10 (VC) - Body ground
      Always
      10 kΩ or higher
      I32-21 (E1) - Body ground
      I32-22 (VSSR) - Body ground
      I32-11 (HSSR) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)


← Power Mirrors do not Return to Memorized Position (Sep 2011 – Dec 2011)Reverse Shift-linked Function of Power Mirrors does not Operate (Sep 2011 – Dec 2011) →