DATA LIST / ACTIVE TEST
System information · Vehicles built from Sep 2011
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List / All Data.
According to the display on the intelligent tester, read the Data List.
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Mirror Selection SW (R)
Mirror master switch signal for RH mirror / ON or OFF
ON: Switch is in R position
OFF: Switch is off or in L position
-
Mirror Selection SW (L)
Mirror master switch signal for LH mirror / ON or OFF
ON: Switch is in L position
OFF: Switch is off or in R position
-
Mirror Position SW (R)
Mirror control switch signal (right) / ON or OFF
ON: Right switch is on
OFF: Any switch except right is on or all switches are off
-
Mirror Position SW (L)
Mirror control switch signal (left) / ON or OFF
ON: Left switch is on
OFF: Any switch except left is on or all switches are off
-
Mirror Position SW (Up)
Mirror control switch signal (up) / ON or OFF
ON: Up switch is on
OFF: Any switch except up is on or all switches are off
-
Mirror Position SW (Dwn)
Mirror control switch signal (down) / ON or OFF
ON: Down switch is on
OFF: Any switch except down is on or all switches are off
-
Outer Mirror Fold SW
Mirror retract switch signal / ON or OFF
ON: Switch is on (retracting)
OFF: Switch is off
-
Mirror Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Mirror Memory No.1*
Mirror position memorized in seat memory switch memory1 / ON or OFF
ON: Memorized
OFF: Not memorized
-
Mirror Memory No.2*
Mirror position memorized in seat memory switch memory2 / ON or OFF
ON: Memorized
OFF: Not memorized
-
Mirror Memory No.3*
Mirror position memorized in seat memory switch memory3 / ON or OFF
ON: Memorized
OFF: Not memorized
-
RH Mir Position Sensor V
Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
Within range from 0 to 5 V
-
RH Mir Position Sensor H
Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
Within range from 0 to 5 V
-
LH Mir Position Sensor V
Driver side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
Within range from 0 to 5 V
-
LH Mir Position Sensor H
Driver side mirror vertical sensor voltage / MIN: 0, MAX: 5 V
Within range from 0 to 5 V
-
- HINT:
- *: w/ Seat Position Memory System
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Mirror / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Mirror Tester Display
Test Part
Control Range
Diagnostic Note
RH Mirror Up/Down
Mirror vertical operation
UP / OFF / DOWN
-
RH Mirror Right/Left
Mirror horizontal operation
RIGHT / OFF / LEFT
-
LH Mirror Up/Down
Mirror vertical operation
UP / OFF / DOWN
-
LH Mirror Right/Left
Mirror horizontal operation
RIGHT / OFF / LEFT
-
Mirror Fold
Mirror retract operation
FOLD / OFF
-
Mirror Return
Mirror retract operation
RETURN / OFF
-