Power Mirrors do not Return to Memorized Position
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
SYSTEM DESCRIPTION
When the seat memory switch 1, seat memory switch 2 or seat memory switch 3 is pressed, the position control ECU and switch mirror position signal is sent through the CAN communication line to the outer mirror control ECU. The outer mirror control ECU then activates the mirror control motors to move the mirrors to the previously recorded positions.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC |
Use the intelligent tester to check if the CAN communication system is functioning normally.
Result Result
Proceed to
CAN DTC is not output
A
CAN DTC is output (for LHD)
B
CAN DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK POWER MIRROR CONTROL FUNCTION |
Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.
- OK:
- Mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY) |
Check the Data List for proper functioning of the mirror position memory (Click here).
Mirror Tester Display
Measurement Item/Display
Normal Condition
Diagnostic Note
Mirror Memory No.1
Mirror position memorized in seat memory switch memory1 / ON or OFF
ON: Memorized
OFF: Not memorized
-
Mirror Memory No.2
Mirror position memorized in seat memory switch memory2 / ON or OFF
ON: Memorized
OFF: Not memorized
-
Mirror Memory No.3
Mirror position memorized in seat memory switch memory3 / ON or OFF
ON: Memorized
OFF: Not memorized
-
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR) |
Check the Data List for proper functioning of the mirror position sensor (Click here).
Mirror Tester Display
Measurement Item/Display
Normal Condition
Diagnostic Note
RH Mir Position Sensor V
RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
Within range from 0 to 5 V
-
RH Mir Position Sensor H
RH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V
Within range from 0 to 5 V
-
LH Mir Position Sensor V
LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
Within range from 0 to 5 V
-
LH Mir Position Sensor H
LH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V
Within range from 0 to 5 V
-
- OK:
- When mirror control switch is operated, voltage changes within range shown in above chart.
Result Result
Proceed to
LH side mirror does not operate normally
A
RH side mirror does not operate normally
B
Mirror operates normally
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK OUTER MIRROR CONTROL ECU |


for LHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
I18-2 (LVC) - I18-3 (LE1)
Engine switch on (IG)
4.7 to 5.5 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I18-3 (LE1) - Body ground
Always
Below 1 Ω
for RHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
I24-2 (LVC) - I24-3 (LE1)
Engine switch on (IG)
4.7 to 5.5 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I24-3 (LE1) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU) |
for LHD:

Disconnect the I18 ECU connector.
Disconnect the I15 mirror connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I18-2 (LVC) - I15-8 (VC)
Always
Below 1 Ω
I18-3 (LE1) - I15-17 (E1)
I18-4 (VSR) - I15-18 (VSRL)
I18-5 (HSRL) - I15-9 (HSRL)
I15-8 (VC) - Body ground
Always
10 kΩ or higher
I15-17 (E1) - Body ground
I15-18 (VSRL) - Body ground
I15-9 (HSRL) - Body ground
for RHD:
Disconnect the I24 ECU connector.
Disconnect the I15 mirror connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I24-2 (LVC) - I15-8 (VC)
Always
Below 1 Ω
I24-3 (LE1) - I15-17 (E1)
I24-4 (VSR) - I15-18 (VSRL)
I24-5 (HSRL) - I15-9 (HSRL)
I15-8 (VC) - Body ground
Always
10 kΩ or higher
I15-17 (E1) - Body ground
I15-18 (VSRL) - Body ground
I15-9 (HSRL) - Body ground
|
|
||||
| OK | ||
| ||
| 7. CHECK OUTER MIRROR CONTROL ECU |


for LHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
I18-22 (RVC) - I18-23 (RE1)
Engine switch on (IG)
4.7 to 5.5 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I18-23 (RE1) - Body ground
Always
Below 1 Ω
for RHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
I24-22 (RVC) - I24-23 (RE1)
Engine switch on (IG)
4.7 to 5.5 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I24-23 (RE1) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU) |
for LHD:

Disconnect the I18 ECU connector.
Disconnect the I7 mirror connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I18-22 (RVC) - I7-8 (VC)
Always
Below 1 Ω
I18-23 (RE1) - I7-17 (E1)
I18-24 (VSRR) - I7-18 (VSSR)
I18-25 (HSRR) - 7-9 (HSSR)
I7-8 (VC) - Body ground
Always
10 kΩ or higher
I7-17 (E1) - Body ground
I7-18 (VSSR) - Body ground
I7-9 (HSSR) - Body ground
for RHD:
Disconnect the I24 ECU connector.
Disconnect the I7 mirror connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I24-22 (RVC) - I7-8 (VC)
Always
Below 1 Ω
I24-23 (RE1) - I7-17 (E1)
I24-24 (VSRR) - I7-18 (VSSR)
I24-25 (HSRR) - 7-9 (HSSR)
I7-8 (VC) - Body ground
Always
10 kΩ or higher
I7-17 (E1) - Body ground
I7-18 (VSSR) - Body ground
I7-9 (HSSR) - Body ground
|
|
||||
| OK | ||
| ||
