2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1900/73 Short in Front Pretensioner Squib RH Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The front pretensioner squib RH circuit consists of the center airbag sensor and the front seat outer belt RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1900/73
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib RH circuit during the primary check.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1901/73
When one of the following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the front pretensioner squib RH circuit for 2 seconds.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1902/73
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib RH circuit for 0.5 seconds.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1903/73
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib RH circuit for 0.5 seconds.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C178002E07
C178002E09

INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).


1. CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)

  1. C173789E06
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front seat outer belt RH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 or B1903 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)

2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the No. 2 floor wire connector (on the front seat outer belt RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


3. CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)

  1. C173790E05
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L13-1 (R+) - Body ground
    Ignition switch ON
    Below 1 V
    L13-2 (R-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L13-1 (R+) - L13-2 (R-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L13-1 (R+) - L13-2 (R-)
    Always
    1 MΩ or higher
    L13-1 (R+) - Body ground
    Always
    1 MΩ or higher
    L13-2 (R-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK CENTER AIRBAG SENSOR

  1. C146261E19
    Connect the connectors to the front seat outer belt RH and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 or B1903 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1865/65 Short in Front Passenger Side Knee Airbag Squib Circuit (+ B1866/65, B1867/65, B1868/65) (from Jan 2012)B1900/73 Short in Front Pretensioner Squib RH Circuit (+ B1901/73, B1902/73, B1903/73) (from Jan 2012) →