2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1835/58 Short in Curtain Shield Squib LH Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The curtain shield squib LH circuit consists of the center airbag sensor and the curtain shield airbag LH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1835/58
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the curtain shield squib LH circuit during the primary check.
  2. A curtain shield squib LH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly LH (Curtain shield squib LH)
  3. Center airbag sensor assembly
B1836/58
When one of the following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the curtain shield squib LH circuit for 2 seconds.
  2. A curtain shield squib LH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly LH (Curtain shield squib LH)
  3. Center airbag sensor assembly
B1837/58
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the curtain shield squib LH circuit for 0.5 seconds.
  2. A curtain shield squib LH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly LH (Curtain shield squib LH)
  3. Center airbag sensor assembly
B1838/58
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the curtain shield squib LH circuit for 0.5 seconds.
  2. A curtain shield squib LH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly LH (Curtain shield squib LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C178002E03

INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).


1. CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)

  1. C148894E06
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the curtain shield airbag LH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835, B1836, B1837 or B1838 is not output.

    HINT:
    Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH (Click here)

2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the floor wire connectors (on the curtain shield airbag LH side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3. CHECK FLOOR WIRE (CURTAIN SHIELD AIRBAG LH CIRCUIT)

  1. C148895E09
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K6-1 (ICL+) - Body ground
    Ignition switch ON
    Below 1 V
    K6-2 (ICL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K6-1 (ICL+) - K6-2 (ICL-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K6-1 (ICL+) - K6-2 (ICL-)
    Always
    1 MΩ or higher
    K6-1 (ICL+) - Body ground
    Always
    1 MΩ or higher
    K6-2 (ICL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


4. CHECK CENTER AIRBAG SENSOR

  1. C146259E17
    Connect the connectors to the curtain shield airbag LH and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835, B1836, B1837 or B1838 is not output.

    HINT:
    Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1830/57 Short in Curtain Shield Squib RH Circuit (+ B1831/57, B1832/57, B1833/57) (from Jan 2012)B1835/58 Short in Curtain Shield Squib LH Circuit (+ B1836/58, B1837/58, B1838/58) (from Jan 2012) →