INSTALLATION
Removal / installation · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the LH side.
- Use the same procedures for the LH side and RH side.
| 1. INSTALL REAR AIRBAG SENSOR |
Check that the ignition switch is turned off.

Check that the cable is disconnected from the battery negative (-) terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Install the rear airbag sensor with the bolt.
- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
- NOTICE:
- If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
- When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
- If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
Check that there is no looseness in the installation parts of the rear airbag sensor.
Connect the connector.
| 2. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/ Sliding Roof) |
![]() ![]() |
- HINT:
- When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }


w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip.


w/ Rear No. 2 Seat, except Face to Face Seat Type:

Install the rear No. 2 seat belt anchor with the bolt.- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
Install the rear No. 1 seat belt anchor with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 3 claws to install the cover.

| 3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/o Sliding Roof) |
![]() ![]() |
- HINT:
- When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }


w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip.


w/ Tonneau Cover:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the screw and clip.


w/ Rear No. 2 Seat, except Face to Face Seat Type:

Install the rear No. 2 seat belt anchor with the bolt.- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
Install the rear No. 1 seat belt anchor with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 3 claws to install the cover.

| 4. INSTALL REAR SEAT COVER CAP (w/ Sliding Roof) |
![]() ![]() |
- HINT:
- Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
| 5. INSTALL REAR SEAT COVER CAP (w/o Sliding Roof) |
![]() ![]() |
- HINT:
- Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
| 6. INSTALL REAR DOOR SCUFF PLATE LH (w/ Sliding Roof) |
![]() ![]() |
Attach the 3 claws and 4 clips to install the scuff plate.
Install the screw.
| 7. INSTALL REAR DOOR SCUFF PLATE LH (w/o Sliding Roof) |
![]() ![]() |
Attach the 3 claws and 4 clips to install the scuff plate.
Install the screw.
| 8. INSTALL REAR STEP COVER (w/ Sliding Roof) |
![]() ![]() |
- HINT:
- Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
| 9. INSTALL REAR STEP COVER (w/o Sliding Roof) |
![]() ![]() |
- HINT:
- Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
| 10. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/ Sliding Roof) |
![]() ![]() |
Attach the 6 clips to install the support plate.
| 11. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Sliding Roof) |
![]() ![]() |
Attach the 6 clips to install the support plate.
| 12. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Split Bench Seat Type) |
Install the rear No. 2 seat assembly LH (Click here).
| 13. INSTALL REAR NO. 2 SEAT ASSEMBLY LH |
Install the rear No. 2 seat assembly LH (Click here).
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 15. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).





