2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR NO. 2 SEAT ASSEMBLY LH
  1. Remove the rear No. 2 seat assembly LH (Click here).


3. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Split Bench Seat Type)
  1. Remove the rear No. 2 seat assembly LH (Click here).


4. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/ Sliding Roof)

B181672
  1. Detach the 6 clips and remove the support plate.


5. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Sliding Roof)

B181672
  1. Detach the 6 clips and remove the support plate.


6. REMOVE REAR STEP COVER (w/ Sliding Roof)

B181673

HINT:
Use the same procedure to remove the step cover on the other side.

  1. Detach the 2 claws and remove the step cover.


7. REMOVE REAR STEP COVER (w/o Sliding Roof)

B181673

HINT:
Use the same procedure to remove the step cover on the other side.

  1. Detach the 2 claws and remove the step cover.


8. REMOVE REAR DOOR SCUFF PLATE LH (w/ Sliding Roof)

B181674
  1. Remove the screw.

  1. Detach the 3 claws and 4 clips, and remove the scuff plate.


9. REMOVE REAR DOOR SCUFF PLATE LH (w/o Sliding Roof)

B181674
  1. Remove the screw.

  1. Detach the 3 claws and 4 clips, and remove the scuff plate.


10. REMOVE REAR SEAT COVER CAP (w/ Sliding Roof)

B190187E01

HINT:
Use the same procedure to remove the rear seat cover cap on the other side.

  1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

    HINT:
    Tape the screwdriver tip before use.


11. REMOVE REAR SEAT COVER CAP (w/o Sliding Roof)

B190187E01

HINT:
Use the same procedure to remove the rear seat cover cap on the other side.

  1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

    HINT:
    Tape the screwdriver tip before use.


12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/ Sliding Roof)

B182644

HINT:
When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. B181687
    Detach the 3 claws and remove the cover.

  1. B181689
    Remove the bolt and rear No. 1 seat belt anchor.

  1. B181691
    w/ Rear No. 2 Seat, except Face to Face Seat Type:
    Remove the bolt and rear No. 2 seat belt anchor.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Remove the clip and bolt.

    2. Detach the 18 clips and 2 claws.

    3. w/o Rear Air Conditioning System:
      Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

    4. w/ Rear Air Conditioning System:
      Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

      B186889

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Remove the clip.

    2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

      B190221


13. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH (w/o Sliding Roof)

B182644

HINT:
When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. B181687
    Detach the 3 claws and remove the cover.

  1. B181689
    Remove the bolt and rear No. 1 seat belt anchor.

  1. B181691
    w/ Rear No. 2 Seat, except Face to Face Seat Type:
    Remove the bolt and rear No. 2 seat belt anchor.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Remove the clip and bolt.

    2. Detach the 18 clips and 2 claws.

    3. w/o Rear Air Conditioning System:
      Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

    4. w/ Rear Air Conditioning System:
      Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

      B186889

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Remove the clip.

    2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

      B190221

  1. w/ Tonneau Cover:

    1. Remove the screw and clip.

    2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

      B186437


14. REMOVE REAR AIRBAG SENSOR

  1. B181652
    Remove the bolt and rear airbag sensor.

  1. Disconnect the connector.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →