Rain Sensor Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The auto wiper system adjusts the wiper speed to the optimum speed based on the amount of rain. The rain sensor mounted on the windshield detects rainfall. This system operates when the windshield wiper switch is set to AUTO. The rain sensor sensitivity can be adjusted with the rain sensor adjusting switch. Signals are sent to the windshield wiper ECU from the windshield wiper switch through the CAN line, and from the rains sensor through the LIN line. Based on these signals, the windshield wiper ECU operates the wiper and determines its operation speed.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WIPER |
Check the symptoms of the wiper. Check if the causes of the symptoms are any of the following conditions shown in the charts.
It is Raining but Wiper does not Operate Condition
Note
Windshield wiper switch in position other than AUTO
Wiper only operates at AUTO setting
Rain sensor temperature is -10°C (14°F) or less, or 70°C (158°F) or more
- To prevent improper operation, wiper does not operate when rain sensor temperature is -10°C (14°F) or less
- To prevent damage to rain sensor, wiper does not operate when outside temperature is 70°C (158°F) or more, or when interior temperature of sensor is 90°C (194°F) or more
It is drizzling, or there is scattered rain
If rain droplets do not contact rain sensor, or rain droplets are very small, they are not detected
- To prevent improper operation, wiper does not operate when rain sensor temperature is -10°C (14°F) or less
| Condition |
Note |
| Condensation on windshield |
Wiper may operate if condensation occurs in rain sensor detection area. If condensation recurs after rain sensor detection area is wiped, wiper operation may continue. |
| Sun rays are strong |
If sudden changes in light intensity occur, wiper may operate |
| Sudden temperature changes |
If sudden changes in temperature occur (A/C heater is used in winter, etc.), wiper may operate |
| Object is contacting rain sensor |
If inner mirror contacts or strikes rain sensor, wiper may operate |
| Windshield wiper switch off by AUTO |
Wiper operates 1 time after windshield wiper switch is turned off by AUTO |
| Condition |
Note |
|
Rain sensor detects rain amount when wipers are operating. When rain is not completely wiped off by wipers, decrease in ability to detect amount of rain occurs. |
|
|
| Wiper volume is set to minimum |
Minimum wiper volume setting is designed to be non-sensitive (for users who prefer non-sensitive operation), resulting in irregular wiper operation |
| Problem with wiper motor position signal |
When wiper motor position signal has chattering, wiper may operate excessively. During auto wiper operation inspection, if wiper operates several times, and replacement of rain sensor does not correct problem, wiper motor may be malfunctioning. |
- OK:
- Causes of symptoms are one or more of above conditions
|
|
||||
| OK | ||
| ||
| 2. CHECK WIPER OPERATION |
Set the windshield wiper switch to the LO and HI setting, and check that the wipers operate normally.
- OK:
- Wipers operate normally
|
|
||||
| OK | |
| 3. CHECK WINDSHIELD WIPER SWITCH |
Set the windshield wiper switch to AUTO, and check the problem symptom.
Result Result
Proceed to
It is raining but wiper does not operate
A
It is not raining but wiper operates
B
|
|
||||
| A | |
| 4. CHECK OPERATION OF WIPER |
Check operation of the wipers.
Result Result
Proceed to
Wiper does not operate normally
A
It is raining but wiper does not operate
B
|
|
||||
| A | |
| 5. CHECK WIPER RUBBER |
Activate the washer and check the wiping ability of the wiper.
- OK:
- No residue after wipe
|
|
||||
| OK | |
| 6. READ VALUE USING INTELLIGENT TESTER (COMBINATION SWITCH) |
Check the Data List for proper functioning of the combination switch.
Combination Switch: Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
F Wiper AUTO Switch
Front wiper AUTO switch / ON or OFF
ON: Front wiper switch in AUTO position
OFF: Wiper switch not in AUTO position
-
- OK:
- Windshield wiper switch operates.
|
|
||||
| OK | |
| 7. CHECK RAIN SENSOR |
Check that the rain sensor is installed properly.
- OK:
- When viewed from outside of vehicle, rain sensor tape is not peeling and has no air bubbles or dust on it, and sensor has not come off bracket
|
|
||||
| OK | |
| 8. READ VALUE USING INTELLIGENT TESTER (RAIN SENSOR) |
Check the Data List for proper functioning of the rain sensor.
Rain Sensor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Rain Sensor Cold
Rain sensor cold / COLD or OK
COLD: Front wiper switch in AUTO position
OK: Wiper switch not in AUTO position
-
Rain Sensor Hot
Rain sensor cold / HOT or OK
HOT: Front wiper switch in AUTO position
OK: Wiper switch not in AUTO position
-
- OK:
- Rain sensor operates.
|
|
||||
| OK | |
| 9. CHECK RAIN SENSOR |
Set the windshield wiper switch to AUTO. Flatten the end of a cotton swab soaked with water so that it is 4 to 6 mm (0.157 to 0.236 in.) wide. Touch the swab to the rain sensor detection area and check that the wiper LO operation occurs once.


Result Result
Proceed to
Wiper does not operate
A
Wiper operates normally
B
Any other operation
C
|
|
||||
|
|
||||
| A | ||
| ||
| 10. CHECK RAIN SENSOR |
Check that the rain sensor is installed properly.
- OK:
- When viewed from outside of vehicle, rain sensor tape is not peeling and has no air bubbles or dust on it, and sensor has not come off bracket
|
|
||||
| OK | ||
| ||
