2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Front Wiper Motor Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The windshield wiper ECU controls the wiper motor.

WIRING DIAGRAM

E138460E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT WIPER MOTOR)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the front wiper motor.

    NOTICE:
    When a Body No. 5 (windshield wiper ECU) related front wiper switch is on, Active Test items related to the front wiper switch are prohibited (double operation prohibition). Check that the front wiper switches are off before performing Active Test.

    Body No. 5 
    Item
    Test Details
    Control Range
    Diagnostic Note
    Wiper Mot (HI)
    Wiper motor HI operation
    ON / OFF
    -
    Wiper Mot (LO)
    Wiper motor LO operation
    ON / OFF
    -

    OK:
    Front wiper motor operates.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FRONT WIPER MOTOR

  1. E147181E01
    Remove the front wiper motor (Click here).

  1. Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.

    OK:
    for LHD 
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (+1)
    Battery negative (-) → Terminal 5 (E)
    Motor operates at low speed
    Battery positive (+) → Terminal 4 (+2)
    Battery negative (-) → Terminal 5 (E)
    Motor operates at high speed
    for RHD 
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 5 (+1)
    Battery negative (-) → Terminal 4 (E)
    Motor operates at low speed
    Battery positive (+) → Terminal 3 (+2)
    Battery negative (-) → Terminal 4 (E)
    Motor operates at high speed



NG
REPLACE FRONT WIPER MOTOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FRONT WIPER MOTOR - WINDSHIELD WIPER ECU AND BODY GROUND)

  1. E157245E01
    Disconnect the A22 motor connector.

  1. Disconnect the E83 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A22-2 (B) - E83-8 (WIG)
    Always
    Below 1 Ω
    A22-1 (+1) - E83-1 (+1)
    A22-4 (+2) - E83-2 (+2)
    A22-3 (+S) - E83-7 (+SM)
    A22-5 (E) - Body ground
    A22-3 (+S) - Body ground
    Always
    10 kΩ or higher
    A22-2 (B) - Body ground
    A22-4 (+2) - Body ground
    A22-1 (+1) - Body ground
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A22-2 (B) - E83-8 (WIG)
    Always
    Below 1 Ω
    A22-5 (+1) - E83-1 (+1)
    A22-3 (+2) - E83-2 (+2)
    A22-1 (+S) - E83-7 (+SM)
    A22-4 (E) - Body ground
    A22-1 (+S) - Body ground
    Always
    10 kΩ or higher
    A22-2 (B) - Body ground
    A22-3 (+2) - Body ground
    A22-5 (+1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE WINDSHIELD WIPER ECU (Click here)


← Headlight Signal Circuit (from Jan 2012)Front Wiper Motor Circuit (from Jan 2012) →