2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

DESCRIPTION

for RHD:
The seat belt buckle switch RH circuit consists of the center airbag sensor and the front seat inner belt RH. DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.
for LHD:
The seat belt buckle switch LH circuit consists of the center airbag sensor and the front seat inner belt LH.
DTC B1656/38 is recorded when a malfunction is detected in the seat belt buckle switch LH circuit.
for RHD 
DTC Code
DTC Detection Condition
Trouble Area
B1655/37
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch RH circuit for 2 seconds.
  2. A front seat inner belt RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat inner belt assembly RH (Seat belt buckle switch RH)
  3. Center airbag sensor assembly
for LHD 
DTC Code
DTC Detection Condition
Trouble Area
B1656/38
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.
  2. A front seat inner belt LH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C253566E06
C174608E05
C253566E07
C174608E04

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK VEHICLE CONDITION
  1. Check vehicle condition.

    Result 
    Result
    Proceed to
    for LHD
    A
    for RHD
    B



B
Go to step 9
A


2. CHECK FOR DTC

  1. C174605E02
    Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656 is not output.

    HINT:
    Codes other than DTC B1656 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the front seat inner belt LH.

  1. Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C263305E01

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K10-6 (LBE+) - Body ground
    Ignition switch ON
    Below 1 V
    K10-7 (LBE-) - Body ground
    Ignition switch ON
    Below 1 V

  1. w/ Side Airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-6 (LBE+) - K10-7 (LBE-)
      Always
      Below 1 Ω

    5. Disconnect a service wire from connector B.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-6 (LBE+) - K10-7 (LBE-)
      Always
      1 MΩ or higher
      K10-6 (LBE+) - Body ground
      Always
      1 MΩ or higher
      K10-7 (LBE-) - Body ground
      Always
      1 MΩ or higher

  1. w/o Side airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Using a service wire, connect terminals 11 (LBE+) and 12 (LBE-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-6 (LBE+) - K10-7 (LBE-)
      Always
      Below 1 Ω

    5. Disconnect a service wire from connector B.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-6 (LBE+) - K10-7 (LBE-)
      Always
      1 MΩ or higher
      K10-6 (LBE+) - Body ground
      Always
      1 MΩ or higher
      K10-7 (LBE-) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


6. CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)

  1. C174605E02
    Connect the connector to the center airbag sensor and the front seat inner belt LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656 is not output.

    HINT:
    Codes other than DTC B1656 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. REPLACE FRONT SEAT INNER BELT LH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt LH (Click here).

    HINT:
    Perform the inspection using parts from a normally functioning vehicle if possible.


NEXT


8. CHECK CENTER AIRBAG SENSOR

  1. C174605E02
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656 is not output.

    HINT:
    Codes other than DTC B1656 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

9. CHECK FOR DTC

  1. C146230E14
    Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Code other than DTC B1655 may be output at this time, but they are not related to this check.



NG
Go to step 10
OK

USE SIMULATION METHOD TO CHECK (Click here)

10. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and front seat inner belt RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


11. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the front seat inner belt RH.

  1. Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


12. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C263306E01

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L33-6 (RBE+) - Body ground
    Ignition switch ON
    Below 1 V
    L33-7 (RBE-) - Body ground
    Ignition switch ON
    Below 1 V

  1. w/ Side Airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Using a service wire, connect terminals 15 (RBE+) and 23 (RBE-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L33-6 (RBE+) - L33-7 (RBE-)
      Always
      Below 1 Ω

    5. Disconnect a service wire from connector B.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L33-6 (RBE+) - L33-7 (RBE-)
      Always
      1 MΩ or higher
      L33-6 (RBE+) - Body ground
      Always
      1 MΩ or higher
      L33-7 (RBE-) - Body ground
      Always
      1 MΩ or higher

  1. w/o Side airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Using a service wire, connect terminals 15 (RBE+) and 14 (RBE-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L33-6 (RBE+) - L33-7 (RBE-)
      Always
      Below 1 Ω

    5. Disconnect a service wire from connector B.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L33-6 (RBE+) - L33-7 (RBE-)
      Always
      1 MΩ or higher
      L33-6 (RBE+) - Body ground
      Always
      1 MΩ or higher
      L33-7 (RBE-) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


13. CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

  1. C146230E14
    Connect the connector to the center airbag sensor and the front seat inner belt RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Codes other than DTC B1655 may be output at this time, but they are not related to this check.



NG
Go to step 14
OK

USE SIMULATION METHOD TO CHECK (Click here)

14. REPLACE FRONT SEAT INNER BELT RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt RH (Click here).

    HINT:
    Perform the inspection using parts from a normally functioning vehicle if possible.


NEXT


15. CHECK CENTER AIRBAG SENSOR

  1. C146230E14
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Codes other than DTC B1655 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH


← B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Sep 2011 – Dec 2011)B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction (Sep 2011 – Dec 2011) →