2011-2013 Land Cruiser · Service Manual Power Source / Network

U1111 Lost Communication with Body No. 5 Module

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
U1111
There is no communication from the windshield wiper ECU.
  1. Power source circuit of windshield wiper ECU
  2. Windshield wiper ECU CAN branch wire or connector
  3. Windshield wiper ECU
  1. For vehicles with the rain sensor.

WIRING DIAGRAM

C177598E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR OPEN IN CAN BUS WIRE (WINDSHIELD WIPER ECU CAN BRANCH WIRE)

  1. E191882E03
    Disconnect the E85 windshield wiper ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E85-6 (CANH) - E85-5 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Windshield Wiper ECU)



NG
REPAIR OR REPLACE WINDSHIELD WIPER ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER ECU - BATTERY AND BODY GROUND)

  1. E191883E04
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E83 windshield wiper ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E83-5 (IG1I) - Body ground
    Ignition switch ON
    11 to 14 V
    E83-8 (WIG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E85-10 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Windshield Wiper ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE WINDSHIELD WIPER ECU (Click here)


← U1111 Lost Communication with Body No. 5 Module (Sep 2011 – Dec 2011)U1115 Lost Communication with Tilt and Telescopic Module (Sep 2011 – Dec 2011) →