2011-2013 Land Cruiser · Service Manual Power Source / Network

U1115 Lost Communication with Tilt and Telescopic Module

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
U1115
There is no communication from the multiplex tilt and telescopic ECU.
  1. Power source circuit of multiplex tilt and telescopic ECU
  2. Multiplex tilt and telescopic ECU CAB branch wire or connector
  3. Multiplex tilt and telescopic ECU
  1. For vehicles with the power tilt and power telescopic steering column system.

WIRING DIAGRAM

C150442E13

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)

  1. C245313E05
    Disconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E27-5 (CANP) - E27-14 (CANN)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)
OK


4. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)

  1. C245313E06
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E27-2 (+B) - Body ground
    Always
    11 to 14 V
    E27-9 (ECUB) - Body ground
    Always
    11 to 14 V
    E27-8 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E27-11 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)


← U1115 Lost Communication with Tilt and Telescopic Module (Sep 2011 – Dec 2011)U1126 Lost Communication with Parking Assist ECU (Sep 2011 – Dec 2011) →