P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low
- P0048 Turbocharger/Supercharger Boost Control "A" Circuit High
- P004B Turbocharger/Supercharger Boost Control Solenoid "B" Circuit Range/Performance
- P004C Turbocharger/Supercharger Boost Control Solenoid "B" Circuit Low
- P004D Turbocharger/Supercharger Boost Control Solenoid "B" Circuit High
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
These DTCs indicates that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets the criteria, the ECM sets a DTC and illuminates the MIL immediately.The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty-cycle of the DC motor in accordance with the driving condition.
If the nozzle vane is stuck closed (DC motor stuck off), the drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), the drivability may deteriorate at intermediate throttle or the engine power may be in sufficient.


| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 5 seconds |
Either of the following conditions are met when the motor is driving (1 trip detection logic):
|
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 1 second |
Both of following conditions are met for 1 second or more when the motor is driving (1 trip detection logic):
|
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 1 second |
DC motor current is 6.5 A or more for 0.5 seconds or more when the motor is operating (1 trip detection logic). |
|
- HINT:
- If DTC P0046, P0047, P0048, P004B, P004C and/or P004D is stored, the following symptoms may appear.
- Stuck closed malfunction:
- Vehicle surge when driving with full load
- Stuck open malfunction:
- Lack of power
- Vehicle surge or hesitation under light or medium load
- White smoke
- Stuck closed malfunction:
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. INSPECT TURBO MOTOR DRIVER (for Bank 1 and Bank 2) |
Remove the rear fender splash shield sub-assembly RH.
Remove the front fender liner LH.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- HINT:
- Record the output DTCs.
Clear the DTCs (Click here).
Turn the ignition switch off.
Interchange the connectors for the turbo motor driver of bank 1 and bank 2.

Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
DTCs do not change
A
DTCs change
B
No DTC output
C
|
|
||||
|
|
||||
| A | |
| 2. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR) (for Bank 1 or Bank 2) |
Disconnect the DC motor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for Bank 1 Tester Connection
Condition
Specified Condition
1 (M-) - 2 (M+)
Always
1 to 100 Ω
- Standard Resistance:
for Bank 2 Tester Connection
Condition
Specified Condition
1 (M2-) - 2 (M2+)
Always
1 to 100 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER) |
Disconnect the DC motor connector.

Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for Bank 1 Tester Connection
Condition
Specified Condition
C90-1 (M-) - Turbo motor driver connector-2 (M-)
Always
Below 1 Ω
C90-2 (M+) - Turbo motor driver connector-1 (M+)
Always
Below 1 Ω
for Bank 2 Tester Connection
Condition
Specified Condition
z67-1 (M2-) - Turbo motor driver connector-2 (M2-)
Always
Below 1 Ω
z67-2 (M2+) - Turbo motor driver connector-1 (M2+)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for Bank 1 Tester Connection
Condition
Specified Condition
C90-1 (M-) or Turbo motor driver connector-2 (M-) - Body ground
Always
10 kΩ or higher
C90-2 (M+) or Turbo motor driver connector-1 (M+) - Body ground
Always
10 kΩ or higher
for Bank 2 Tester Connection
Condition
Specified Condition
z67-1 (M2-) or Turbo motor driver connector-2 (M2-) - Body ground
Always
10 kΩ or higher
z67-2 (M2+) or Turbo motor driver connector-1 (M2+) - Body ground
Always
10 kΩ or higher
|
|
||||
|
|
||||
| 4. REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2) |
Replace turbocharger sub-assembly (for Bank 1 or Bank 2) (Click here).
|
|
||||
| 5. REPLACE TURBO MOTOR DRIVER (for Bank 1 or Bank 2) |
Replace turbo motor driver (for Bank 1 or Bank 2) (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
| 8. INSPECT TURBOCHARGER SUB - ASSEMBLY |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm up.
Move the shift lever to 3rd and accelerate the vehicle with the accelerator fully open.
Stop the vehicle
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
DTC P0046, P0047, P0048, P004B, P004C and/or P004D are output
A
No DTC output
B
- HINT:
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
- "Target Booster Pressure" and "MAP" in the snapshot can be used to heck the operation of the turbocharger. If "MAP" does not follow "Target Booster Pressure", the turbocharger nozzle vane may be stuck or the movement may be irregular.
- When the engine speed is 2500 to 3000 rpm with the accelerator pedal fully depressed, "MAP" is within +/- 10 kPa* of "Target Booster Pressure" (not immediately after beginning of acceleration).
-
* If the turbocharger pressure does not reach a specified value, it cannot be determined whether the system is normal by checking whether "MAP" is within +/-10 kPa of "Target Booster Pressure"
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.


- HINT:
- Compare "MAP" with "Target Booster Pressure" at the point indicated by the arrow (↑) in the illustration.
|
|
||||
| B | ||
| ||
