2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

NOTICE:
w/ DPF:
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines,


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE ENGINE ASSEMBLY
(Click here)

4. REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE (for Bank 1)

  1. A170301
    Remove the 2 bolts and No. 1 engine oil level dipstick guide.

  1. Remove the O-ring from the No. 1 engine oil level dipstick.


5. REMOVE NO. 1 INTAKE AIR CONNECTOR PIPE (for Bank 1)

  1. A174753
    Disconnect the 4 connectors.

  1. Using a clip remover, detach the 5 wire harness clamps.

  1. A177381
    Loosen the hose clamp, and remove the bolt and No. 1 intake air connector pipe.


6. REMOVE NO. 2 VENTILATION HOSE (for Bank 1)

A264021E01
Text in Illustration 
*A
w/ DPF
*B
w/o DPF

7. REMOVE NO. 2 TURBO WATER HOSE (for Bank 1)

A267247

8. REMOVE BREATHER PLUG RH (for Bank 1)

  1. A267248
    Disconnect the hose.

  1. Detach the clamp and remove the breather plug RH.


9. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (for Bank 1)

  1. A264022E01
    Remove the 3 bolts and No. 1 exhaust manifold heat insulator.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


10. DISCONNECT NO. 1 OUTLET TURBO OIL HOSE (for Bank 1)

A267249

11. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY (for Bank 1)

  1. A177401
    Disconnect the water hose.

  1. Remove the 3 bolts, 2 nuts, No. 1 turbo water pipe and gasket.


12. REMOVE NO. 1 TURBOCHARGER STAY (for Bank 1)

  1. A177403
    Remove the 2 bolts and No. 1 turbocharger stay.


13. REMOVE NO. 1 VENTILATION TUBE SUB-ASSEMBLY (for Bank 1)

  1. A264023
    Disconnect the hose.

  1. Remove the union bolt, bolt, No. 1 ventilation tube and gasket.


14. REMOVE NO. 1 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD RH (for Bank 1)

  1. A177405
    Remove the union bolt and gasket, and disconnect the No. 1 inlet turbo oil pipe from the cylinder block.

  1. Remove the 10 nuts, 10 collars and No. 1 turbocharger with exhaust manifold RH.

    A264024E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket.

  1. A264026
    w/ DPF:
    Remove the 4 bolts, No. 1 exhaust manifold pipe and 2 gaskets.

  1. Remove the 2 nuts and bolt, and separate the No. 1 turbocharger and exhaust manifold RH.

    A264025E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket from the No. 1 turbocharger.


15. REMOVE NO. 1 INLET COMPRESSOR ELBOW (for Bank 1)

  1. A174717
    Remove the 2 bolts, No. 1 inlet compressor elbow and gasket.


16. REMOVE NO. 1 TURBO OIL PIPE (for Bank 1)

  1. A170298
    Remove the 2 bolts, No. 1 turbo oil pipe and gasket.


17. REMOVE NO. 1 INLET TURBO OIL PIPE SUB-ASSEMBLY (for Bank 1)

  1. A170313
    Remove the union bolt, bolt, No. 1 inlet turbo oil pipe and gasket.


18. REMOVE NO. 3 VENTILATION HOSE (for Bank 2)

A264027E01
Text in Illustration 
*A
w/ DPF
*B
w/o DPF

19. REMOVE BREATHER PLUG LH (for Bank 2)

  1. A267263E01
    Disconnect the hose.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. w/o DPF:
    Detach the clamp.

  1. Remove the breather plug LH.


20. REMOVE NO. 2 TURBO WATER HOSE (for Bank 2)

A267250

21. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (for Bank 2)

  1. A264028E01
    Remove the 3 bolts and No. 2 exhaust manifold heat insulator.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


22. REMOVE NO. 3 TURBO WATER PIPE SUB-ASSEMBLY (for Bank 2)

  1. A177386
    Remove the 2 bolts, union bolt, No. 3 turbo water pipe and gasket.


23. REMOVE FRONT WATER BY-PASS JOINT (for Bank 2)

  1. A177435
    Remove the front water by-pass joint and gasket.


24. REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY (for Bank 2)

  1. A267251
    Disconnect the water hose.

  1. Remove the union bolt, bolt, No. 2 turbo water pipe and gasket.


25. REMOVE NO. 2 OUTLET TURBO OIL HOSE (for Bank 2)

A267252

26. REMOVE NO. 2 TURBOCHARGER STAY (for Bank 2)

  1. A267253
    Remove the 2 bolts and No. 2 turbocharger stay.


27. REMOVE NO. 2 VENTILATION TUBE SUB-ASSEMBLY (for Bank 2)

  1. Disconnect the hose.

    A264029E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the union bolt, bolt, No. 2 ventilation tube and gasket.


28. REMOVE NO. 2 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD LH (for Bank 2)

  1. A179471
    Disconnect the 2 connectors from the turbocharger.

  1. A177391
    Remove the union bolt and gasket, and disconnect the No. 2 inlet turbo oil pipe from the No. 1 oil pan.

  1. Remove the 10 nuts, 10 collars and No. 2 turbocharger with exhaust manifold LH.

    A264030E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket.

  1. A264032
    w/ DPF:
    Remove the 4 bolts, No. 2 exhaust manifold pipe and 2 gaskets.

  1. A264031E01
    Remove the 3 nuts, and separate the No. 2 turbocharger and exhaust manifold LH.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket from the turbocharger.


29. REMOVE NO. 2 INLET COMPRESSOR ELBOW (for Bank 2)

  1. A174716
    Remove the 2 bolts, No. 2 inlet compressor elbow and gasket.


30. REMOVE NO. 2 TURBO OIL PIPE (for Bank 2)

  1. A170314
    Remove the 2 bolts, No. 2 turbo oil pipe and gasket.


31. REMOVE NO. 2 INLET TURBO OIL PIPE SUB-ASSEMBLY (for Bank 2)

  1. A177395
    Remove the union bolt, bolt, No. 2 inlet turbo oil pipe and gasket.


32. REPLACE STUD BOLT

HINT:
If a stud bolt is deformed or its threads are damaged, replace it.

  1. For No. 1 Turbocharger:

    1. Using an E10 "TORX" wrench, replace the stud bolts labeled A and B shown in the illustration below.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Replace the stud bolts labeled C shown in the illustration below.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


      A177307E02

  1. A177308E01
    For No. 2 Turbocharger:
    Using an E10 "TORX" wrench, replace the stud bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A264033E01
    For Exhaust Manifold LH:
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF
    Using an E10 "TORX" wrench, replace the stud bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (Sep 2011 – Dec 2011) →