2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P00AF Turbocharger/Supercharger Boost Control "A" Module Performance

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, turbo motor driver and ECM.
The turbocharger has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure. When the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.
The turbocharger actuator, which consists of the DC motor and the nozzle vane position sensor, is built on the turbocharger sub-assembly, and activates the nozzle vane. The nozzle vane position sensor detects the opening angle of the nozzle vane. The turbo motor driver receives an opening angle request from the ECM and a nozzle vane position signal from the nozzle vane position sensor. Based on these signals, the turbo motor driver operates the DC motor and adjusts the nozzle vane opening angle. The turbo motor driver sends the status as a turbo driver status signal to the ECM
The ECM sends a target nozzle vane position signal to the turbo motor driver to obtain the nozzle vane position for the optimal boost pressure in accordance with the driving conditions.
A182385E04
P00AF 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After idling for 5 seconds
When a communication error occurs between the turbo motor driver (for Bank 1) and ECM (1 trip detection logic).
  1. Turbo motor driver (for Bank 1)
  2. Open or short in turbo motor driver (for Bank 1) circuit
  3. Turbo motor driver (for Bank 1) ground problem
  4. ECM
P00B0 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After idling for 5 seconds
When a communication error occurs between the turbo motor driver (for Bank 2) and ECM (1 trip detection logic).
  1. Turbo motor driver (for Bank 2)
  2. Open or short in turbo motor driver (for Bank 2) circuit
  3. Turbo motor driver (for Bank 2) ground problem
  4. ECM

WIRING DIAGRAM

A182474E01

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Excessive electrical noise, such as from wireless radios or electrical modifications, may cause a DTC to be stored.

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. INSPECT TURBO MOTOR DRIVER (POWER SOURCE CIRCUIT)

  1. A184085E01
    Disconnect the turbo motor driver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for Bank 1 
    Tester Connection
    Condition
    Specified Condition
    Turbo motor driver connector-3 (+B) - Turbo motor driver connector-4 (GND)
    Ignition switch ON
    11 to 14 V
    for Bank 2 
    Tester Connection
    Condition
    Specified Condition
    Turbo motor driver connector-3 (+B2) - Turbo motor driver connector-4 (GND2)
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Bank 1 
    Tester Connection
    Condition
    Specified Condition
    Turbo motor driver connector-4 (GND) - Body ground
    Always
    Below 1 Ω
    for Bank 2 
    Tester Connection
    Condition
    Specified Condition
    Turbo motor driver connector-4 (GND2) - Body ground
    Always
    Below 1 Ω



NG
Go to step 5
OK


2. INSPECT TURBO MOTOR DRIVER (for Bank 1 and Bank 2)
  1. Remove the rear fender splash shield sub-assembly RH.

  1. Remove the front fender liner LH.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

HINT:
Record the output DTCs.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. A176217
    Interchange the connectors for the turbo motor driver of bank 1 and bank 2.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    DTCs change
    B
    DTCs do not change
    A



B
Go to step 6
A


3. CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)
  1. Disconnect the turbo motor driver connector.

  1. A184083E01
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-49 (VNTO) - B-4 (VNTO)
    Always
    Below 1 Ω
    C45-50 (VNTI) - B-3 (VNTI)
    Always
    Below 1 Ω
    C45-47 (VNO2) - D-4 (VNO2)
    Always
    Below 1 Ω
    C45-48 (VNI2) - D-3 (VNI2)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-49 (VNTO) - B-4 (VNTO)
    Always
    Below 1 Ω
    C46-50 (VNTI) - B-3 (VNTI)
    Always
    Below 1 Ω
    C46-47 (VNO2) - D-4 (VNO2)
    Always
    Below 1 Ω
    C46-48 (VNI2) - D-3 (VNI2)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-49 (VNTO) or B-4 (VNTO) - Body ground
    Always
    10 kΩ or higher
    C45-50 (VNTI) or B-3 (VNTI) - Body ground
    Always
    10 kΩ or higher
    C45-47 (VNO2) or D-4 (VNO2) - Body ground
    Always
    10 kΩ or higher
    C45-48 (VNI2) or D-3 (VNI2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-49 (VNTO) or B-4 (VNTO) - Body ground
    Always
    10 kΩ or higher
    C46-50 (VNTI) or B-3 (VNTI) - Body ground
    Always
    10 kΩ or higher
    C46-47 (VNO2) or D-4 (VNO2) - Body ground
    Always
    10 kΩ or higher
    C46-48 (VNI2) or D-3 (VNI2) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 5
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
5. REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 7
6. REPLACE TURBO MOTOR DRIVER (for Bank 1 or Bank 2)
  1. Replace the turbo motor driver (for Bank 1 or Bank 2) (Click here).


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. After starting the engine, idle it for 5 seconds.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0093 Fuel System Leak Detected - Large Leak (from Jan 2012)P00AF Turbocharger/Supercharger Boost Control "A" Module Performance (+ P00B0) (from Jan 2012) →