2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P1258 VNT Position Sensor Range/Performance Bank 2 Sensor 1

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the turbo motor driver. The turbo motor driver determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.
A183002E01
P1258 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
The difference between VTI2 and VTA2 voltage is 0.8 V or more for 0.5 seconds (1 trip detection logic).
Nozzle vane position sensor (turbocharger sub-assembly)
P1259 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTI2 voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver
P1260 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTI2 voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver
P1262 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA2 voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver
P1263 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA2 voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver
P2563 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
The difference between VTA1 and VTA voltage is 0.8 V or more for 0.5 seconds (1 trip detection logic).
Nozzle vane position sensor (turbocharger sub-assembly)
P2564 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA1 voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver
P2565 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA1 voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver
P2588 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver
P2589 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. Turbo motor driver

HINT:
If DTC P1258, P1259, P1260, P1262, P1263, P2563, P2564, P2565, P2588 and/or P2589 is stored, the following symptoms may appear:
Stuck open malfunction:
  1. - Lack of power
  2. - Vehicle surge or hesitation under light or medium load
  3. - White smoke


WIRING DIAGRAM

A182511E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT TURBO MOTOR DRIVER (for Bank 1 and Bank 2)
  1. Remove the rear fender splash shield sub-assembly RH.

  1. Remove the front fender liner LH.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

HINT:
Record the output DTCs.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. A176217
    Interchange the connectors for the turbo motor driver of bank 1 and bank 2.

  1. Turn the ignition switch to ON for 1 second.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    DTCs change
    B
    DTCs do not change
    A



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - NOZZLE VANE POSITION SENSOR)

  1. A184079E01
    Disconnect the nozzle vane position sensor connector.

  1. Disconnect the turbo motor driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for Bank 1 
    Tester Connection
    Condition
    Specified Condition
    Turbo motor driver connector-5 (VTA1) - Nozzle vane position sensor connector-1 (VTA1)
    Always
    Below 1 Ω
    Turbo motor driver connector-2 (VNE2) - Nozzle vane position sensor connector-2 (VNE2)
    Always
    Below 1 Ω
    Turbo motor driver connector-8 (VNVC) - Nozzle vane position sensor connector-3 (VNVC)
    Always
    Below 1 Ω
    Turbo motor driver connector-6 (VTA) - Nozzle vane position sensor connector-4 (VTA)
    Always
    Below 1 Ω
    Turbo motor driver connector-1 (E2S) - Nozzle vane position sensor connector-5 (E2S)
    Always
    Below 1 Ω
    Turbo motor driver connector-7 (VCS) - Nozzle vane position sensor connector-6 (VCS)
    Always
    Below 1 Ω
    for Bank 2 
    Tester Connection
    Condition
    Specified Condition
    Turbo motor driver connector-5 (VTI2) - Nozzle vane position sensor connector-1 (VTI2)
    Always
    Below 1 Ω
    Turbo motor driver connector-2 (VE2) - Nozzle vane position sensor connector-2 (VE2)
    Always
    Below 1 Ω
    Turbo motor driver connector-8 (VNC2) - Nozzle vane position sensor connector-3 (VNC2)
    Always
    Below 1 Ω
    Turbo motor driver connector-6 (VTA2) - Nozzle vane position sensor connector-4 (VTA2)
    Always
    Below 1 Ω
    Turbo motor driver connector-1 (E2S2) - Nozzle vane position sensor connector-5 (E2S2)
    Always
    Below 1 Ω
    Turbo motor driver connector-7 (VCS2) - Nozzle vane position sensor connector-6 (VCS2)
    Always
    Below 1 Ω


Standard Resistance (Check for Short):
for Bank 1 
Tester Connection
Condition
Specified Condition
Turbo motor driver connector-5 (VTA1) or Nozzle vane position sensor connector-1 (VTA1) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-2 (VNE2) or Nozzle vane position sensor connector-2 (VNE2) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-8 (VNVC) or Nozzle vane position sensor connector-3 (VNVC) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-6 (VTA) or Nozzle vane position sensor connector-4 (VTA) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-1 (E2S) or Nozzle vane position sensor connector-5 (E2S) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-7 (VCS) or Nozzle vane position sensor connector-6 (VCS) - Body ground
Always
10 kΩ or higher
for Bank 2 
Tester Connection
Condition
Specified Condition
Turbo motor driver connector-5 (VTI2) or Nozzle vane position sensor connector-1 (VTI2) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-2 (VE2) or Nozzle vane position sensor connector-2 (VE2) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-8 (VNC2) or Nozzle vane position sensor connector-3 (VNC2) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-6 (VTA2) or Nozzle vane position sensor connector-4 (VTA2) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-1 (E2S2) or Nozzle vane position sensor connector-5 (E2S2) - Body ground
Always
10 kΩ or higher
Turbo motor driver connector-7 (VCS2) or Nozzle vane position sensor connector-6 (VCS2) - Body ground
Always
10 kΩ or higher



NG
Go to step 5
OK


3. REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2) (NOZZLE VANE POSITION SENSOR)
  1. Replace the turbocharger sub-assembly (for Bank 1 or Bank 2) (Click here).



NEXT
Go to step 6
4. REPLACE TURBO MOTOR DRIVER (for Bank 1 or Bank 2)
  1. Replace the turbo motor driver (for Bank 1 or Bank 2) (Click here).



NEXT
Go to step 6
5. REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT


6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch off and leave the vehicle for 15 seconds.

  1. Turn the ignition switch to ON for 1 second.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out

    1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

    2. Input DTC P1258, P1259, P1260, P1262, P1263, P2563, P2564, P2565, P2588 and/or P2589.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, idle the engine.


NEXT

END


← P1251 Turbocharger / Supercharger Overboost Condition (Too High) (from Jan 2012)P1258 VNT Position Sensor Range/Performance Bank 2 Sensor 1 (+ 9 more codes) (from Jan 2012) →