2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1429/29 Rear Air Foot Duct Sensor Circuit on Front Passenger Side

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The air duct temperature sensor RH*1 or LH*2 (for front passenger side) detects the duct temperature and sends the appropriate signals to the air conditioning amplifier assembly.
DTC Code
DTC Detection Condition
Trouble Area
B1429/29
An open or short in the air duct temperature sensor RH*1 or LH*2 circuit.
  1. Air duct temperature sensor RH*1
  2. Air duct temperature sensor LH*2
  3. Harness or connector (air duct temperature sensor RH)*1
  4. Harness or connector (air duct temperature sensor LH)*2
  5. Air conditioning amplifier assembly

HINT:
*1: for LHD
*2: for RHD


WIRING DIAGRAM

E156584E36
E156584E37

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (AIR DUCT TEMPERATURE SENSOR)
  1. Use the Data List to check if the air duct temperature sensor RH*1 or LH*2 (for front passenger side) is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Foot Duct Sensor (Rear P)
    Min.: -12.7°C (9.14°F)
    Max.: 76.55°C (169.79°F)
    Actual air duct temperature sensor (for passenger side) displayed
    Open in the circuit: -12.7°C (9.14°F)
    Short in the circuit: 76.55°C (169.79°F)

    HINT:
    *1: for LHD
    *2: for RHD

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

2. CHECK AIR DUCT TEMPERATURE SENSOR
E160938E01
  1. for LHD

    1. Remove the air duct temperature sensor RH (Click here).

  1. for RHD

    1. Remove the air duct temperature sensor LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 2 (-)
    at 10°C (50°F)
    9.4 to 10.5 kΩ
    at 15°C (59°F)
    7.5 to 8.3 kΩ
    at 20°C (68°F)
    6.0 to 6.5 kΩ
    at 25°C (77°F)
    4.5 to 5.2 kΩ
    at 30°C (86°F)
    3.8 to 4.2 kΩ
    at 35°C (95°F)
    3.1 to 3.4 kΩ
    at 40°C (104°F)
    2.5 to 2.8 kΩ
    at 45°C (113°F)
    2.0 to 2.3 kΩ
    at 50°C (122°F)
    1.6 to 2.0 kΩ
    at 55°C (131°F)
    1.3 to 1.6 kΩ
    at 60°C (140°F)
    1.1 to 1.4 kΩ

    NOTICE:
    1. Touching the sensor even slightly may change the resistance value. Hold the connector of the sensor.
    2. When measuring the resistance, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).
    If the resistance value is not as specified, replace the sensor.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE AIR DUCT TEMPERATURE SENSOR RH (Click here)

C
REPLACE AIR DUCT TEMPERATURE SENSOR LH (Click here)
A


3. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR DUCT TEMPERATURE SENSOR)
E156820E06
  1. for LHD

    1. Disconnect the L12 sensor connector.

    2. Disconnect the E35 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E35-26 (TR4) - L12-1 (+)
      Always
      Below 1 Ω
      E35-12 (SG-9) - L12-2 (-)
      E35-26 (TR4) - Body ground
      Always
      10 kΩ or higher
      E35-12 (SG-9) - Body ground

  1. E156820E07
    for RHD
    1. Disconnect the K21 sensor connector.

    2. Disconnect the E35 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E35-25 (TR3) - K21-1 (+)
      Always
      Below 1 Ω
      E35-34 (SGND) - K21-2 (-)
      E35-25 (TR3) - Body ground
      Always
      10 kΩ or higher
      E35-34 (SGND) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← B1429/29 Rear Air Foot Duct Sensor Circuit on Front Passenger Side (Sep 2011 – Dec 2011)B1441/41 Air Mix Damper Control Servo Motor Circuit (Passenger Side) (Sep 2011 – Dec 2011) →