2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1445 Cool Air Bypass Damper Control

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1445
The air outlet damper position does not change for 30 seconds or more when the air conditioning amplifier assembly operates the No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo).
  1. No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E180810E78

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (COOL AIR BYPASS PULSE)
  1. Use the Data List to check if the No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Cool Air Bypass Pulse
    No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) target pulse / Min.: 0, Max.: 255
    1. Shut and DEF mode: 6 (pulse)
    2. Shut: 28 (pulse)
    3. Open: 57 (pulse)
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOL AIR BYPASS PULSE)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Cool Air Bypass Pulse
    No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo)
    Min.: 0, Max.: 255
    -

    OK:
    The No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) pulse signal changes according to the target pulse specified by the Active Test.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

3. REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (COOLER BYPASS DAMPER SERVO)
  1. Temporarily replace the No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo).

    1. for LHD: Click here.
    2. for RHD: Click here.

    HINT:
    Since the No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) cannot be inspected while it is removed from the vehicle, replace the No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1445 is not output
    A
    DTC B1445 is output
    B



B
Go to step 4
A

END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY [COOLER BYPASS DAMPER SERVO] IS FAULTY)

4. REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Temporarily replace the air conditioning harness assembly with a new or normally functioning one.

    1. for LHD: Click here.
    2. for RHD: Click here.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1445 is not output
    A
    DTC B1445 is output
    B



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)


← B1443 Air Outlet Damper Control Servo Motor Circuit (from Jan 2012)B1445 Cool Air Bypass Damper Control (from Jan 2012) →