B1443 Air Outlet Damper Control Servo Motor Circuit
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.- HINT:
- Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1443 |
The air outlet damper position does not change for 30 seconds or more when the air conditioning amplifier assembly operates the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (AIR OUTLET SERVO PULSE [D]) |
Use the Data List to check if the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) is functioning properly (Click here).
Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Outlet Servo Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) target pulse / Min.: 0, Max.: 255
- FACE: 117 (pulse)
- B/L: 93 (pulse)
- FOOT: 41 (pulse)
- F/D: 18 (pulse)
- DEF: 6 (pulse)
-
- OK:
- The display is as specified in the normal condition column.
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table)
A
OK (When troubleshooting according to the DTC)
B
NG
C
- FACE: 117 (pulse)
|
|
||||
|
|
||||
| A | ||
| ||
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIR OUTLET SERVO PULSE [D]) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) operates (Click here).
Air Conditioner Tester Display
Test Part
Control Range
Diagnostic Note
Air Outlet Servo Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo)
Min.: 0, Max.: 255
-
- OK:
- The No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) pulse signal changes according to the target pulse specified by the Active Test.
|
|
||||
| OK | ||
| ||
| 3. REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO) |
Temporarily replace the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo).
- for LHD: Click here.
- for RHD: Click here.
- HINT:
- Since the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) with a new or normally functioning one.
- for LHD: Click here.
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1443 is not output
A
DTC B1443 is output
B
|
|
||||
| A | ||
| ||
| 4. REPLACE AIR CONDITIONING HARNESS ASSEMBLY |
Temporarily replace the air conditioning harness assembly with a new or normally functioning one.
- for LHD: Click here.
- for RHD: Click here.
- for LHD: Click here.
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1443 is not output
A
DTC B1443 is output
B
|
|
||||
| A | ||
| ||
