2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL WATER INLET PIPE
  1. Apply soapy water to 2 new O-rings and install them to the inlet pipe.

  1. Install the inlet pipe to the No. 1 heat exchanger cover.


2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Apply a light coat of engine oil to a new oil pump gasket.

  1. Install the oil pump gasket.

  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring.

  1. Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

    A178520E03

    Text in Illustration 
    *1
    Continuous line area
    *2
    Dashed line area
    *3
    Diagonal line area
    -
    -

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


    1. A150825E08

      Apply Seal Packing as Follows:
      Area
      Seal Packing Diameter
      Application Position from Inside Edge of Cover
      Continuous Line Area
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      2.5 mm (0.0984 in.)
      Dashed Line Area
      6.4 mm (0.252 in.) or more, or within OK area shown in illustration
      7.0 mm (0.276 in.)
      Diagonal Line Area
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      5.5 mm (0.217 in.)

      Text in Illustration 
      *1
      Seal Packing Thickness mm (in.)
      *2
      Seal Packing Width mm (in.)
      *3
      Seal Packing Thickness
      *4
      Seal Packing Width
      *5
      OK Area

    NOTICE:
    1. When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

  1. A162541
    Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.

  1. A162542E04
    Temporarily install the timing chain cover with the 28 bolts and nut.

    Standard Bolt:
    Item
    Length
    Thread Diameter
    Bolt A
    25 mm (0.984 in.)
    8 mm (0.315 in.)
    Bolt B
    55 mm (2.17 in.)
    8 mm (0.315 in.)
    Bolt C
    70 mm (2.76 in.)
    8 mm (0.315 in.)
    Bolt D
    35 mm (1.38 in.)
    10 mm (0.394 in.)
    Bolt E
    55 mm (2.17 in.)
    10 mm (0.394 in.)
    Bolt F
    80 mm (3.15 in.)
    10 mm (0.394 in.)

    Text in Illustration 
    *1
    Nut

    NOTICE:
    Make sure that there is no oil on the bolt threads.

  1. A174145E01
    Tighten the 3 bolts in several steps in the sequence shown in the illustration.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }

  1. A163330E01
    Temporarily install the fluid coupling bracket with the 4 bolts.

    Standard Bolt:
    Item
    Length
    Thread Diameter
    Bolt A
    70 mm (2.76 in.)
    8 mm (0.315 in.)
    Bolt B
    80 mm (3.15 in.)
    10 mm (0.394 in.)

  1. A162527
    Temporarily install the belt tensioner with the standard bolt and 6 mm hexagon wrench bolt.

  1. A174146E01
    Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }

  1. A162544E01
    Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    1. Do not start the engine for at least 2 hours after installing.

    2. A162545E01
      After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.


3. INSTALL SPARK PLUG TUBE GASKET

  1. A100218E07
    Using a cutter knife, cut off the seal part of the removed gasket.
    Text in Illustration 
    V100155
    Area to cut off

  1. A164316E02
    Using the removed gasket and a hammer, tap in a new gasket until it stops.
    Text in Illustration 
    *1
    Removed Gasket
    *2
    New Gasket

    HINT:
    If the removed gasket does not fit on the new one, correct the removed one with pliers.

  1. Apply a light coat of MP grease to the lip of the gasket.

  1. Return the 4 ventilation baffle plate claws to the original positions.


4. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).

  1. Install a new gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.

  1. A162546E06
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A162523E02
    Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.

    Torque:
    for bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    except bolt A:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.


5. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
  1. Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).

  1. Install a new gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.

  1. A162547E06
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A162525E02
    Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.

    Torque:
    for bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    except bolt A:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.

  1. Install the noise filter to the cylinder head cover with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


6. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 8 ignition coils with the 8 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


7. INSTALL CRANKSHAFT TIMING GEAR KEY
  1. Install the crankshaft timing gear key to the crankshaft.


8. CONNECT WIRE HARNESS CLAMP BRACKET
  1. Connect the bracket to the timing chain cover with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


9. INSTALL CRANKSHAFT PULLEY

  1. A164230E06
    Align the pulley set key with the key groove of the pulley, and slide on the pulley.

  1. Using SST, install the pulley set bolt.

    SST
    09213-70011  
    09330-00021  

    Torque:
    300 N*m{ 3059 kgf*cm , 221 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    V100135
    Turn


10. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
  1. Install the idler pulley with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


11. INSTALL WATER PUMP PULLEY

  1. A162556E01
    Temporarily install the pulley with the 4 bolts.

  1. Using SST, hold the pulley and tighten the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


12. INSTALL WATER INLET HOUSING

  1. A162555E04
    Install a new gasket to the timing chain cover.

  1. Install the water inlet with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Text in Illustration 
    *1
    Gasket


13. INSTALL NO. 1 ENGINE COVER

14. INSTALL NO. 2 ENGINE COVER

15. INSTALL FRONT WATER BY-PASS JOINT
  1. Install 2 new gaskets and the water by-pass joint with the 4 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the No. 2 water by-pass hose to the water by-pass joint.


16. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Connect the 2 hoses.

  1. Install the water by-pass pipe with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


17. INSTALL NO. 1 WATER BY-PASS HOSE
  1. Install the No. 1 water by-pass hose by connecting the hose to the water inlet housing and front water by-pass joint.


18. INSTALL GENERATOR ASSEMBLY
  1. Install the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the generator with the 3 bolts and nut.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the harness bracket to the generator with the bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.

  1. Connect the generator connector.


19. CONNECT OIL COOLER PIPE ASSEMBLY
  1. Connect the oil cooler pipe with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


20. CONNECT VANE PUMP ASSEMBLY

A163333E04

HINT:
Before performing the following procedures, move the spacer until the vane pump can be installed.
Text in Illustration 
*1
Spacer

  1. Connect the vane pump to the timing chain cover with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


21. INSTALL INTAKE MANIFOLD

  1. A184486E01
    Place 2 new gaskets on the intake manifold.
    Text in Illustration 
    *1
    Gasket

  1. Place the intake manifold on the cylinder head.

  1. Install and uniformly tighten the 8 bolts and 2 nuts in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the wire bracket to the intake manifold with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 3 wire clamps to the 3 wire brackets.

  1. Install the No. 3 engine cover.

  1. Install the No. 1 engine cover sub-assembly.

  1. Connect the purge VSV connector.

  1. Connect the purge line hose to the purge VSV.

  1. Connect the vacuum switching valve connector (for ACIS).

  1. Connect the No. 1 ventilation hose.

  1. Connect the 2 water by-pass hoses.

  1. Connect the throttle body connector.

  1. Connect the ventilation hose to the ventilation pipe of the cylinder head cover LH and RH.


22. INSTALL OIL FILTER BRACKET
  1. Apply a light coat of engine oil to 2 new O-rings.

  1. Install the 2 O-rings to the timing chain cover.

  1. Install the oil filter bracket with the 2 nuts and 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }


23. INSTALL NO. 1 OIL COOLER BRACKET
  1. Connect the ground wire to the cylinder block.

  1. Install the oil cooler bracket with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


24. INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Connect the 4 hoses.

  1. Install the water by-pass pipe with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


25. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


    NOTICE:
    A178540E02
    Do not allow adhesive to contact the oil hole.

    Text in Illustration 
    *1
    Oil Hole

  1. Install the oil pressure sender gauge.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.

  1. Connect the sender gauge connector.


26. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the dipstick.

  1. Connect the wire harness clamp.


27. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, its threads and its O-ring groove.

  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

  1. Set a new oil filter element to the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A207200E02
    Using SST, tighten the oil filter cap.
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    1. When tightening the oil filter cap, do not remove the oil filter bracket clip.
    2. Make sure that the oil filter is installed securely as shown in the illustration.
    3. Be careful that the O-ring does not get caught between any surrounding parts.

  1. A237033E01
    Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between any surrounding parts.

  1. Install the No. 2 engine under cover seal with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


28. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

  1. A165142E04
    Connect the fuel tube with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *A
    LH Side
    *B
    RH Side


29. CONNECT COOLER COMPRESSOR ASSEMBLY

  1. A178491E01
    Install the cooler compressor with the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 3 bolts and nut.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts and nut in the order shown in the illustration to install the cooler compressor.


30. CONNECT WATER PIPE AND HOSE SUB-ASSEMBLY
  1. Connect the water pipe and hose to the cylinder head cover with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the 3 hoses.


31. CONNECT ENGINE WIRE
  1. Connect the 2 clamps and power steering oil pressure switch connector.

  1. Engine Room RH Side:

    1. Connect the 5 clamps.

    2. Connect the throttle position sensor and throttle control motor connector.

    3. Install the ground wire with the 2 bolts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    4. Connect the noise filter connector.

    5. Connect the 2 VVT sensor connectors.

    6. Connect the injector connector.

    7. Connect the 4 ignition coil connectors.

    8. Connect the 2 camshaft timing oil control valve connectors.

  1. Engine Room LH Side:

    1. Connect the cooler compressor connector.

    2. Connect the 3 clamps.

    3. Connect the camshaft position sensor connector.

    4. Connect the 2 camshaft timing oil control valve connectors.

    5. Connect the engine coolant temperature sensor connector.

    6. Connect the 4 clamps.

    7. Install the ground wire with the 2 bolts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    8. Connect the noise filter connector.

    9. Connect the 2 VVT sensor connectors.

    10. Connect the 4 ignition coil connectors.

    11. Connect the injector connector.

    12. Connect the 2 connectors and 2 clips to the engine room junction block.

    13. Install the engine room relay block cover.


32. INSTALL RADIATOR ASSEMBLY
(Click here)

33. INSTALL AIR CLEANER ASSEMBLY
  1. Install the air cleaner with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


34. INSTALL AIR CLEANER HOSE ASSEMBLY

  1. A243381E01
    Install the air cleaner hose so that the protrusion of the air cleaner cap aligns with the groove of the hose as shown in the illustration.
    Text in Illustration 
    *1
    Groove
    *2
    Protrusion

  1. Tighten the 2 clamps.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose.

  1. Connect the No. 2 ventilation hose.


35. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A177597E02
    Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet


36. ADD ENGINE OIL
  1. Add fresh oil and install the oil filler cap.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy-conserving", API grade SM "energy-conserving" or ILSAC multigrade engine oil
    5W-30
    10W-30
    API grade SL and SM multigrade engine oil
    15W-40
    20W-50

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill without oil filter change
    7.1 liters (7.5 US qts, 6.2 Imp. qts)
    Drain and refill with oil filter change
    7.5 liters (7.9 US qts, 6.6 Imp. qts)
    Dry fill
    9.3 liters (9.8 US qts, 8.2 Imp. qts)


37. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    with rear heater
    16.2 liters (17.1 US qts, 14.3 Imp. qts)
    without rear heater
    13.4 liters (14.2 US qts, 11.8 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the reservoir cap.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Check that the coolant level is between the F and L lines.
    If the coolant level is below the L line, repeat all of the procedures above.
    If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.


38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


39. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


40. INSPECT FOR COOLANT LEAK

A178451

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.


41. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the dipstick low level mark and full level mark.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


42. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the No. 2 engine under cover with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


43. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


44. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
  1. Push in the clip to install the front fender splash shield sub-assembly LH.

  1. Install the 3 bolts and screw.


45. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Push in the clip to install the front fender splash shield sub-assembly RH.

  1. Install the 3 bolts and 2 screws.


46. INSTALL FRONT FENDER APRON SEAL FRONT RH
  1. Install the fender apron seal with the 3 clips.


47. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the fender apron seal with the 3 clips.


48. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

49. CONNECT RADIATOR SIDE DEFLECTOR LH
  1. Connect the deflector with the 4 clips.


50. INSTALL TRANSMISSION OIL COOLER AIR DUCT
  1. Install the oil cooler air duct with the 4 bolts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }


51. INSTALL FRONT BUMPER COVER

HINT:
For the front bumper cover with garnish, use the procedure described below.

  1. B232036
    w/ Headlight Cleaner System:
    Connect the headlight cleaner hose.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Connect the No. 4 engine room wire connector.

  1. Attach the 10 claws to install the front bumper cover.

  1. Install the 3 clips, 4 screws and 4 bolts.

  1. Using a T30 "TORX" socket, install the 6 screws.


52. INSTALL RADIATOR GRILLE
  1. w/ Wide View Front Monitor System:

    1. Connect the connector.

  1. Attach the 2 clips and 8 claws to install the radiator grille assembly.

  1. Install the 3 screws.


53. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. Install the radiator support seal with the 7 clips.

    B180890E02

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →