2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. Remove the 7 clips and radiator support seal.

    B180890E02


5. REMOVE RADIATOR GRILLE

  1. B302174E01
    Put protective tape around the radiator grille assembly.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille assembly.

  1. w/ Wide View Front Monitor System:

    1. Disconnect the connector.


6. REMOVE FRONT BUMPER COVER

HINT:
For the front bumper cover with garnish, use the procedure described below.

  1. Put protective tape around the front bumper cover.

    B302149E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B313279E01

    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. Detach the 10 claws and remove the front bumper cover.

    B302150

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Disconnect the No. 4 engine room wire connector and remove the front bumper cover.

  1. B181927
    w/ Headlight Cleaner System:
    Disconnect the headlight cleaner hose and remove the front bumper cover.


7. REMOVE TRANSMISSION OIL COOLER AIR DUCT

  1. A271852
    Remove the 4 bolts and oil cooler air duct.


8. DISCONNECT RADIATOR SIDE DEFLECTOR LH

  1. A271854
    Using a clip remover, remove the 4 clips and disconnect the side deflector.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

10. REMOVE FRONT FENDER APRON SEAL LH

  1. A177004
    Using a clip remover, remove the 3 clips and fender apron seal.


11. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Using a clip remover, remove the 3 clips and fender apron seal.


12. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


13. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


14. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


15. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


16. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A174194
    Remove the 2 bolts and No. 2 engine under cover seal.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


17. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174123E02
    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Tighten the radiator drain cock plug by hand.


18. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A174196E03
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet


19. REMOVE AIR CLEANER HOSE ASSEMBLY

  1. A243375
    Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.


20. REMOVE AIR CLEANER ASSEMBLY

  1. A174195
    Remove the 3 bolts and air cleaner.


21. REMOVE RADIATOR ASSEMBLY
(Click here)

22. DISCONNECT ENGINE WIRE

  1. Engine Room LH Side:

    1. A237015
      Remove the engine room relay block cover.

    2. Disconnect the 2 connectors and 2 clips from the engine room junction block.

    3. A178453
      Disconnect the injector connector.

    4. Disconnect the 4 ignition coil connectors.

    5. Disconnect the 2 VVT sensor connectors.

    6. Disconnect the 4 clamps.

    7. Remove the 2 bolts and ground wire.

    8. Disconnect the noise filter connector.

    9. A174202
      Disconnect the engine coolant temperature sensor connector.

    10. Disconnect the 2 camshaft timing oil control valve connectors.

    11. Disconnect the camshaft position sensor connector.

    12. Disconnect the 3 clamps.

    13. Disconnect the cooler compressor connector.

  1. A237034
    Engine Room RH Side:

    1. Disconnect the 2 camshaft timing oil control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the injector connector.

    4. Disconnect the 2 VVT sensor connectors.

    5. Disconnect the noise filter connector.

    6. Remove the 2 bolts and ground wire.

    7. Disconnect the throttle position sensor and throttle control motor connector.

    8. Disconnect the 5 clamps.

  1. A174204
    Disconnect the 2 clamps and power steering oil pressure switch connector.


23. DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY

  1. A239168
    Disconnect the 3 hoses.

  1. Remove the 2 bolts and disconnect the water pipe and hose from the cylinder head cover.


24. DISCONNECT COOLER COMPRESSOR ASSEMBLY

  1. A178491
    Remove the 3 bolts, nut and stud bolt, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


25. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

  1. A165142E04
    Remove the 2 bolts and disconnect the fuel tube.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side


26. REMOVE OIL FILTER ELEMENT

  1. A094910E10
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A207196
    Remove the oil filter drain plug.

  1. A237032E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A207198
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A207199E02
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A209947E02
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


27. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A174205
    Disconnect the wire harness clamp.

  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


28. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A163657
    Disconnect the sender gauge connector.

  1. A162467
    Remove the oil pressure sender gauge.


29. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A165547
    Remove the 3 bolts.

  1. Disconnect the 4 hoses and remove the water by-pass pipe.


30. REMOVE NO. 1 OIL COOLER BRACKET

  1. A163672
    Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.


31. REMOVE OIL FILTER BRACKET

  1. A162469
    Remove the 2 bolts, 2 nuts and filter bracket.

  1. A162470
    Remove the 2 O-rings.


32. REMOVE INTAKE MANIFOLD

  1. A162091E01
    Disconnect the ventilation hose from the ventilation pipe of the cylinder head cover LH and RH.

  1. A162087
    Disconnect the 2 water by-pass hoses.

  1. Disconnect the throttle body connector.

  1. A184056
    Disconnect the No. 1 ventilation hose.

  1. A162082
    Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.

  1. Disconnect the vacuum switching valve connector (for ACIS).

  1. A162089
    Remove the No. 1 engine cover sub-assembly.

  1. A238871
    Remove the No. 3 engine cover.

  1. A238834
    Disconnect the 3 wire clamps from the 3 wire brackets.

  1. A238832
    Remove the bolt and wire bracket from the intake manifold.

  1. A184053
    Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.


33. DISCONNECT VANE PUMP ASSEMBLY

  1. A163289
    Remove the 2 bolts and disconnect the vane pump.


34. DISCONNECT OIL COOLER PIPE ASSEMBLY

  1. A174185
    Remove the 2 bolts and disconnect the oil cooler pipe.


35. REMOVE GENERATOR ASSEMBLY

  1. A177892
    Disconnect the generator connector.

  1. Open the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the bolt and disconnect the wire harness bracket from the generator.

  1. A177893
    Remove the 3 bolts, nut and generator.

  1. Remove the stud bolt.


36. REMOVE NO. 1 WATER BY-PASS HOSE

  1. A237017
    Remove the No. 1 water by-pass hose by disconnecting the hose from the water inlet housing and front water by-pass joint.


37. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A162551
    Disconnect the 2 hoses.

  1. Remove the 2 bolts and water by-pass pipe.


38. REMOVE FRONT WATER BY-PASS JOINT

  1. A162552
    Disconnect the No. 2 water by-pass hose from the water by-pass joint.

  1. Remove the 4 nuts, water by-pass joint and 2 gaskets.


39. REMOVE NO. 2 ENGINE COVER

A237721

40. REMOVE NO. 1 ENGINE COVER

A237722

41. REMOVE WATER INLET HOUSING

  1. A162554
    Remove the 3 bolts, water inlet housing and gasket.


42. REMOVE WATER PUMP PULLEY

  1. A162556E01
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.


43. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A162557
    Remove the bolt and idler pulley.


44. REMOVE FLUID COUPLING BRACKET

  1. A162558
    Remove the 4 bolts and fluid coupling bracket.


45. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A162527
    Remove the standard bolt, 6 mm hexagon wrench bolt and belt tensioner.


46. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 8 bolts and 8 ignition coils.


47. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A162523
    Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A162524
    Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).


48. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A163381
    Remove the bolt and noise filter.

  1. A162525
    Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A162526
    Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).


49. REMOVE SPARK PLUG TUBE GASKET

A164315E02
  1. Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

  1. Using a screwdriver, pry out the gaskets.

    Text in Illustration 
    *1
    Tape
    V100135
    Pry

    NOTICE:
    1. Be careful not to damage the cylinder head cover.
    2. Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.

    HINT:
    Tape the screwdriver tip before use.


50. REMOVE CRANKSHAFT PULLEY

  1. A164228E04
    Using SST, loosen the crankshaft pulley set bolt until 2 or 3 threads are engaged.
    SST
    09213-70011  
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. A164229E03
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)
    Text in Illustration 
    *a
    Hold
    V100135
    Turn


51. DISCONNECT WIRE HARNESS CLAMP BRACKET

  1. A163733
    Remove the bolt and disconnect the bracket.


52. REMOVE CRANKSHAFT TIMING GEAR KEY

  1. A163993
    Using a screwdriver, remove the timing gear key from the crankshaft.


53. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A237019
    Remove the 28 bolts and nut shown in the illustration.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. A162530
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

    HINT:
    Tape the screwdriver tip before use.

  1. A162531
    Remove the oil pump gasket from the cylinder block.

  1. A164415
    Remove the O-ring from the oil pan.


54. REMOVE WATER INLET PIPE

  1. A162532
    Remove the water inlet pipe.

  1. Remove the 2 O-rings from the water inlet pipe.

← REMOVAL (Sep 2011 – Dec 2011)DISASSEMBLY (from Sep 2011) →