2011-2013 Land Cruiser · Service Manual Power Source / Network

B2321 Driver Side Door ECU Communication Stop

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor LH*1 (RH*2) and main body ECU (cowl side junction block LH) stops for 10 seconds or more.

HINT:
  1. *1: for LHD
  2. *2: for RHD

DTC Code
DTC Detection Condition
Trouble Area
B2321
No communication between the front power window regulator motor LH*1 or RH*2 and main body ECU (cowl side junction block LH) for 10 seconds or more.
  1. Front power window regulator motor LH*1
  2. Front power window regulator motor RH*2
  3. Main body ECU (cowl side junction block LH)
  4. Harness or connector

WIRING DIAGRAM

B173719E22

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

HINT:
DTC B2325 is stored when the communication between the front power window regulator motor and main body ECU (cowl side junction block LH) stops.


1. CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2. CHECK FOR DTC
  1. Recheck for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2321 is output
    A
    DTC B2321 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)
E156403E05
  1. Disconnect the E3 ECU connector.

  1. Disconnect the I12*1 or I4*2 motor connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E3-10 (LIN2) - I12-9 (LIN)*1 or I4-9 (LIN)*2
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (BATTERY VOLTAGE AND BODY GROUND)

  1. B163167E17
    Disconnect the I12*1 or I4*2 motor connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance and voltage according to the value(s) in the tables below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I12-1 (GND)*1 or I4-1 (GND)*2 - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I12-2 (B)*1 or I4-2 (B)*2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Temporarily replace the front power window regulator motor LH*1 or RH*2 with a new or normally functioning one (Click here).

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Clear the DTC (Click here).


NEXT


6. CHECK FOR DTC
  1. Recheck for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2321 is not output
    A
    DTC B2321 is output
    B



B
REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
A

END (FRONT POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)


← B2287 LIN Communication Master Malfunction (from Sep 2011)B2321 Driver Side Door ECU Communication Stop (from Jan 2012) →