2011-2013 Land Cruiser · Service Manual Power Source / Network

B2323 Rear Door RH ECU Communication Stop

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when LIN communication between the rear power window regulator motor RH and main body ECU (cowl side junction block LH) stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2323
No communication between the rear power window regulator motor RH and main body ECU (cowl side junction block LH) for 10 seconds or more.
  1. Rear power window regulator motor RH
  2. Main body ECU (cowl side junction block LH)
  3. Harness or connector

WIRING DIAGRAM

B173719E17

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

HINT:
DTC B2325 is stored when the communication between the rear power window regulator motor and main body ECU (cowl side junction block LH) stops.


1. CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2. CHECK FOR DTC
  1. Recheck for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2323 is output
    A
    DTC B2323 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR POWER WINDOW REGULATOR MOTOR RH)
E156403E03
  1. Disconnect the E3 ECU connector.

  1. Disconnect the J4 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E3-10 (LIN2) - J4-9 (LIN)
    Always
    Below 1 Ω
    E3-10 (LIN2) or J4-9 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (BATTERY VOLTAGE AND BODY GROUND)

  1. B163167E14
    Disconnect the J4 motor connector.

  1. Measure the resistance and voltage according to the value(s) in the tables below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J4-1 (GND) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J4-2 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
  1. Temporarily replace the rear power window regulator motor RH with a new or normally functioning one (Click here).

  1. Clear the DTC (Click here).


NEXT


6. CHECK FOR DTC
  1. Recheck for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2323 is not output
    A
    DTC B2323 is output
    B



B
REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
A

END (REAR POWER WINDOW REGULATOR MOTOR RH IS DEFECTIVE)


← B2322 Front Passenger Side Door ECU Communication Stop (from Jan 2012)B2323 Rear Door RH ECU Communication Stop (from Jan 2012) →