2011-2013 Land Cruiser · Service Manual Vehicle Interior

All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the entry operation and wireless operation door lock function does not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (line is used by entry and wireless); or 2) the door control transmitter.

WIRING DIAGRAM

B185450E01

INSPECTION PROCEDURE

NOTICE:
  1. Before performing the inspection, check that there are no problems related to the "CAN Communication System" and "LIN Communication System".
  2. Check that there are no door control transmitters in the vehicle.
  3. Before performing the inspection, check that DTC B1242 is not output (Click here).


1. CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the master switch door control switch is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. CHECK DOOR CONTROL TRANSMITTER
  1. When another registered door control transmitter is used, check that the wireless and entry function operates normally (Click here).

    Result 
    Result
    Proceed to
    Entry function operates and door control transmitter that did not operate is electrical key transmitter
    A
    Entry function does not operate
    B



B
Go to step 5
A


3. CHECK DOOR CONTROL TRANSMITTER (LED)
  1. Check that the transmitter LED illuminates 3 times when a switch is pressed 3 times.

    Result 
    Result
    Proceed to
    Transmitter LED does not illuminate 3 times when switch is pressed 3 times
    A
    Transmitter LED illuminates 3 times when switch is pressed 3 times
    B
    Transmitter LED does not illuminate second or third time
    C

    HINT:
    If the transmitter LED does not illuminate the second or third time, replace the transmitter battery as it is depleted.



B
REPLACE DOOR CONTROL TRANSMITTER

C
REPLACE TRANSMITTER BATTERY (Click here)
A


4. INSPECT TRANSMITTER BATTERY (VOLTAGE)

  1. Electrical key transmitter

    HINT:
    1. Type A: for Australia
    2. Type B: except Australia

    1. B192058E01
      Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) or less in diameter including wire sheath) with tape or equivalent to the negative terminal (Click here).

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    2. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

    3. Using an oscilloscope, check the transmitter battery voltage waveform.

      HINT:
      When measuring the battery voltage, while operating the lock switch of a door handle, bring the electrical key transmitter within the entry operating range to perform the measurement. For the entry operating range, refer to System Description (Click here).

      B192059E01

      OK:
      Tester Connection
      Tool Setting
      Condition
      Specified Condition
      Battery positive (+) - Battery negative (-)
      0.5 V/DIV., 100 ms/DIV.
      Engine switch off, all doors closed and lock switch pushed
      2.5 to 3.2 V (Refer to the waveform)



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER

5. CHECK WAVE ENVIRONMENT
  1. Bring the door control transmitter near the door control receiver, and perform a wireless and entry function operation check.

    HINT:
    1. When the door control transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Wireless and entry functions operate normally.



NG
Go to step 6
OK

AFFECTED BY WAVE INTERFERENCE

6. INSPECT FUSE (IMB)
  1. Remove the IMB fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IMB fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


7. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BATTERY)

  1. B187926E01
    Disconnect the E29 ECU connector.

  1. Measure the voltage according to the value(s) in the tables below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E29-1 (+B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR CONTROL RECEIVER AND BODY GROUND)
B185451E01
  1. Disconnect the L31 receiver connector.

  1. Disconnect the E29 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E29-29 (RCO) - L31-4 (+5)
    Always
    Below 1 Ω
    E29-38 (RDA) - L31-5 (DATA)
    Always
    Below 1 Ω
    E29-39 (RSSI) - L31-2 (RSSI)
    Always
    Below 1 Ω
    E29-17(E) - Body ground
    Always
    Below 1 Ω
    L31-1 (GND) - Body ground
    Always
    Below 1 Ω
    E29-29 (RCO) or L31-4 (+5) - Body ground
    Always
    10 kΩ or higher
    E29-38 (RDA) or L31-5 (DATA) - Body ground
    Always
    10 kΩ or higher
    E29-39 (RSSI) or L31-2 (RSSI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Temporarily replace the door control receiver with a new one (Click here).

  1. Check that the wireless and entry functions operate normally.

    OK:
    Wireless and entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)


← Entry Answer-back Buzzer does not Sound (from Jan 2012)All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate (from Jan 2012) →