2011-2013 Land Cruiser · Service Manual Vehicle Interior

Rear Door LH Entry Unlock Function does not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If the rear door LH entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be a touch sensor circuit (certification ECU (smart key ECU assembly) → rear door outside handle LH → rear door electrical key oscillator LH).

HINT:
For vehicles with entry function for rear doors.


WIRING DIAGRAM

B186274E07

INSPECTION PROCEDURE


1. CHECK POWER DOOR LOCK OPERATION
  1. When the master switch assembly door control switch is operated, check that the locked doors unlock.

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    1. for LHD

      Main Body 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      DR Door Lock Position SW
      Driver side rear door lock position switch signal / ON or OFF
      ON: Driver side rear door unlocked
      OFF: Driver side rear door locked
      -

      OK:
      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.

    2. for RHD

      Main Body 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      PR Door Lock Position SW
      Passenger side rear door lock position switch signal / ON or OFF
      ON: Passenger side rear door unlocked
      OFF: Passenger side rear door locked
      -

      OK:
      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door LH LOCK/UNLOCK Functions do not Operate) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)
  1. Using the intelligent tester, read the Data List.

    1. for LHD

      Entry & Start 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Dr-Door Touch Sensor
      Driver side rear door touch sensor / ON or OFF
      ON: Touch sensor touched
      OFF: Touch sensor not touched
      -

      OK:
      "ON" (sensor is touched) and "OFF" (sensor is not touched) appears on the screen.

    2. for RHD

      Entry & Start 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Pr-Door Touch Sensor
      Passenger side rear door touch sensor / ON or OFF
      ON: Touch sensor touched
      OFF: Touch sensor not touched
      -

      OK:
      "ON" (sensor is touched) and "OFF" (sensor is not touched) appears on the screen.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)

  1. B187936E05
    Disconnect the E30 ECU connector.

  1. Disconnect the z28 oscillator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    E30-1 (SEL3) - z28-4 (SEL)
    Always
    Below 1 Ω
    E30-28 (SEN3) - z28-6 (SENS)
    Always
    Below 1 Ω
    E30-1 (SEL3) - Body ground
    Always
    10 kΩ or higher
    E30-28 (SEN3) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    E30-2 (SEL4) - z28-4 (SEL)
    Always
    Below 1 Ω
    E30-27 (SEN4) - z28-6 (SENS)
    Always
    Below 1 Ω
    E30-2 (SEL4) - Body ground
    Always
    10 kΩ or higher
    E30-27 (SEN4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE)

  1. B164339E43
    Disconnect the z27 handle connector.

  1. Disconnect the z28 oscillator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z27-6 (SGT) - z28-2 (SGT)
    Always
    Below 1 Ω
    z27-6 (SGT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE DOOR ELECTRICAL KEY OSCILLATOR
  1. Replace the door electrical key oscillator (Click here).


NEXT


7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry function operates normally.

    OK:
    Operates normally.



NG
Go to step 8
OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

8. REPLACE REAR DOOR OUTSIDE HANDLE
  1. Replace the rear door outside handle (Click here).


NEXT


9. CHECK REAR DOOR OUTSIDE HANDLE (OPERATION)
  1. Check that the entry function operates normally.

    OK:
    Operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (REAR DOOR OUTSIDE HANDLE IS DEFECTIVE)


← Front Passenger Side Door Entry Unlock Function does not Operate (from Jan 2012)Rear Door LH Entry Unlock Function does not Operate (from Jan 2012) →