2011-2013 Land Cruiser · Service Manual Vehicle Interior

Front Passenger Side Door Entry Unlock Function does not Operate

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If the front passenger side door entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be a touch sensor circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle → front passenger side door electrical key oscillator).

WIRING DIAGRAM

B186274E06

INSPECTION PROCEDURE


1. CHECK POWER DOOR LOCK OPERATION
  1. When the master switch assembly door control switch is operated, check that the locked doors unlock.

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door Lock Position SW
    Front passenger side door lock position switch signal / ON or OFF
    ON: Front passenger side door unlocked
    OFF: Front passenger side door locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)
  1. Using the intelligent tester, read the Data List.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Door Touch Sensor
    Front passenger side door touch sensor / ON or OFF
    ON: Touch sensor touched
    OFF: Touch sensor not touched
    -

    OK:
    "ON" (sensor is touched) and "OFF" (sensor is not touched) appears on the screen.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)

  1. B187935E06
    Disconnect the E29 ECU connector.

  1. Disconnect the z22 or z24 oscillator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    E29-6 (SEL2) - z22-4 (SEL)
    Always
    Below 1 Ω
    E29-23 (SEN2) - z22-6 (SENS)
    Always
    Below 1 Ω
    E29-6 (SEL2) - Body ground
    Always
    10 kΩ or higher
    E29-23 (SEN2) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    E29-6 (SEL2) - z24-4 (SEL)
    Always
    Below 1 Ω
    E29-23 (SEN2) - z24-6 (SENS)
    Always
    Below 1 Ω
    E29-6 (SEL2) - Body ground
    Always
    10 kΩ or higher
    E29-23 (SEN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)

  1. B164339E56
    Disconnect the z21 or z23 handle connector.

  1. Disconnect the z22 or z24 oscillator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    z21-6 (SGT) - z22-2 (SGT)
    Always
    Below 1 Ω
    z21-6 (SGT) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    z23-6 (SGT) - z24-2 (SGT)
    Always
    Below 1 Ω
    z23-6 (SGT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE DOOR ELECTRICAL KEY OSCILLATOR
  1. Replace the door electrical key oscillator (Click here).


NEXT


7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry function operates normally.

    OK:
    Operates normally.



NG
Go to step 8
OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

8. REPLACE FRONT DOOR OUTSIDE HANDLE
  1. Replace the front door outside handle (Click here).


NEXT


9. CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)
  1. Check that the entry function operates normally.

    OK:
    Operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)


← Front Passenger Side Door Entry Unlock Function does not Operate (Sep 2011 – Dec 2011)Rear Door LH Entry Unlock Function does not Operate (Sep 2011 – Dec 2011) →