2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Light Control Switch Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The main body ECU receives light control switch, dimmer switch and front fog light switch information signals from the headlight dimmer switch.

WIRING DIAGRAM

E159525E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (HEADLIGHT DIMMER SWITCH)
  1. Operate the intelligent tester according to the display and select the "Data List".

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Dimmer switch signal/ON or OFF
    ON: Dimmer switch on
    OFF: Dimmer switch off
    -
    Passing Light SW
    Passing light switch signal/ON or OFF
    ON: Passing light switch on
    OFF: Passing light switch off
    -
    Front Fog Light SW
    Front fog light switch signal/ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Rear Fog Light SW
    Rear fog light switch signal/ON or OFF
    ON: Rear fog light switch on
    OFF: Rear fog light switch off
    -
    Auto Light SW
    Auto light switch signal/ON or OFF
    ON: Auto light switch on
    OFF: Auto light switch off
    -
    Head Light SW (Head)
    Headlight switch signal/ON or OFF
    ON: Headlight switch (Head) on
    OFF: Headlight switch (Head) off
    -
    Head Light SW (Tail)
    Taillight switch signal/ON or OFF
    ON: Headlight switch (Tail) on
    OFF: Headlight switch (Tail) off
    -

    OK:
    When combination light switch operation is performed, the result will be the same as above.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY

  1. E155807E03
    Remove the headlight dimmer switch (Click here).

  1. for LH Side:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      18 (T) - 12 (EL)
      Light control switch tail
      Below 1 Ω
      20 (H) - 12 (EL)
      Light control switch head
      18 (T) - 12 (EL)
      19 (A) - 12 (EL)
      Light control switch AUTO
      4 (BFG) - 3 (LFG)
      Front fog light switch on
      2 (B) - 3 (LFG)
      Rear fog light switch on
      17 (HF) - 12 (EL)
      Dimmer switch flash
      11 (HU) - 12 (EL)
      Dimmer switch hi beam

  1. E159508E02
    for RH Side:
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      13 (T) - 19 (EL)
      Light control switch tail
      Below 1 Ω
      11 (H) - 19 (EL)
      Light control switch head
      13 (T) - 19 (EL)
      12 (AUTO) - 19 (EL)
      Light control switch AUTO
      7 (BFG) - 8 (LFG)
      Front fog light switch on
      9 (B) - 8 (LFG)
      Rear fog light switch on
      14 (HF) - 19 (EL)
      Dimmer switch flash
      20 (HU) - 19 (EL)
      Dimmer switch hi beam



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the E14 switch connector.

  1. for LH Side:

    1. Disconnect the E1, E2 and 2D ECU connectors.E157455E01

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E14-4 (BFG) - E2-28 (FFOG)
      Always
      Below 1 Ω
      E14-2 (B) - E2-9 (RFGO)
      E14-19 (A) - E1-21 (A)
      E14-20 (H) - E2-17 (HEAD)
      E14-18 (T) - E1-23 (TAIL)
      E14-17 (HF) - E1-13 (HF)
      E14-11 (HU) - 2D-13 (HU)
      E14-12 (EL) - Body ground
      E14-3 (LFG) - Body ground
      E14-4 (BFG) - Body ground
      Always
      10 kΩ or higher
      E14-2 (B) - Body ground
      E14-19 (A) - Body ground
      E14-20 (H) - Body ground
      E14-18 (T) - Body ground
      E14-17 (HF) - Body ground
      E14-11 (HU) - Body ground

  1. for RH Side:

    1. Disconnect the E1, E2 and 2D ECU connectors.E157455E02

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E14-7 (BFG) - E2-28 (FFOG)
      Always
      Below 1 Ω
      E14-9 (B) - E2-9 (RFOG)
      E14-12 (A) - E1-21 (A)
      E14-11 (H) - E2-17 (HEAD)
      E14-13 (T) - E1-23 (TAIL)
      E14-14 (HF) - E1-13 (HF)
      E14-20 (HU) - 2D-13 (HU)
      E14-19 (EL) - Body ground
      E14-8 (LFG) - Body ground
      E14-7 (BFG) - Body ground
      Always
      10 kΩ or higher
      E14-9 (B) - Body ground
      E14-12 (A) - Body ground
      E14-11 (H) - Body ground
      E14-13 (T) - Body ground
      E14-14 (HF) - Body ground
      E14-20 (HU) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Light Control Switch Circuit (Sep 2011 – Dec 2011)Headlight Signal Circuit (Sep 2011 – Dec 2011) →