2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Headlight Signal Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The main body ECU receives a headlight Lo switch information signal from the light control switch, and illuminates the headlight low beam.

WIRING DIAGRAM

E157016E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT)
  1. Operate the intelligent tester according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Relay
    Headlight
    ON or OFF
    -

    OK:
    Headlight low beam turns on/turns off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FUSE (HEAD LL, HEAD RL)
  1. Remove the HEAD LL and HEAD RL fuses from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    HEAD LL fuse
    Always
    Below 1 Ω
    HEAD RL fuse



NG
REPLACE FUSE
OK


3. INSPECT HEADLIGHT RELAY (HEAD LO)

  1. A111813E09
    Remove the headlight relay from the engine room relay block (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE HEADLIGHT RELAY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - BODY GROUND)

  1. E160870E01
    Remove the headlight relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Headlight relay terminal 1 - Body ground
    Always
    11 to 14 V
    Headlight relay terminal 5 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - HEADLIGHT AND BODY GROUND)

  1. Remove the headlight relay from the engine room relay block.E160880E01

  1. for LH:

    1. Disconnect the A3 headlight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Headlight relay terminal 3 - A3-2
      Always
      Below 1 Ω
      A3-1 - Body ground
      A3-2 - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the A12 headlight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Headlight relay terminal 3 - A12-2
      Always
      Below 1 Ω
      A12-1 - Body ground
      A12-2 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HEADLIGHT (LOW BEAM)

  1. E147118E06
    Disconnect the 2B ECU connector.

  1. Using a service wire, connect terminal 2B-18 (HRLY) on the wire harness side and body ground.

  1. Check that the headlight low beam illuminates.

    OK:
    Headlight low beam illuminates.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT RELAY - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU


← Light Control Switch Circuit (from Jan 2012)Headlight Signal Circuit (from Jan 2012) →