2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Front Fog Light Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The main body ECU receives a front fog light switch information signal from the light control switch (front fog switch), and illuminates the front fog lights.

WIRING DIAGRAM

E146023E02

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT FOG LIGHT)
  1. Operate the intelligent tester according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Fog Light Relay
    Front fog light
    ON or OFF
    -

    OK:
    Fog light turns on/turns off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FUSE (FR FOG)
  1. Remove the FR FOG fuse from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    FR FOG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3. INSPECT FOG LIGHT RELAY
E121182E06
  1. Remove the fog light relay from the engine room relay block (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE FOG LIGHT RELAY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (FOG LIGHT RELAY - BODY GROUND)
E160901E01
  1. Remove the fog light relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Fog light relay terminal 2 - Body ground
    Light control switch tail
    11 to 14 V
    Fog light relay terminal 5 - Body ground
    Always



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (FOG LIGHT RELAY - FOG LIGHT ASSEMBLY AND BODY GROUND)
E160900E02
  1. Remove the fog light relay from the engine room relay block.

  1. for LH:

    1. Disconnect the B1 fog light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Fog light relay terminal 3 - B1-1
      Always
      Below 1 Ω
      B1-2 - Body ground
      B1-1 - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the B2 fog light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Fog light relay terminal 3 - B2-1
      Always
      Below 1 Ω
      B2-2 - Body ground
      B2-1 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK FRONT FOG LIGHT
E147119E03
  1. Disconnect the E1 ECU connector.

  1. Using a service wire, connect terminal E1-4 (FFGO) on the wire harness side and body ground.

  1. Check that the front fog light illuminates.

    OK:
    Front fog light illuminates.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FOG LIGHT RELAY - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU


← Headlight (HI-BEAM) Circuit (from Jan 2012)Front Fog Light Circuit (from Jan 2012) →