2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Taillight Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The main body ECU receives a light control switch information signal from the headlight dimmer switch, and illuminates the taillights.

WIRING DIAGRAM

E233674E03
E233673E02

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAILLIGHT RELAY)
  1. Operate the intelligent tester according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Taillight Relay
    Taillight
    ON or OFF
    -

    OK:
    Taillight turns on/turns off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FUSE (TAIL FUSE)
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    TAIL fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)

  1. E157348E01
    Disconnect the 2A ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2A-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    for Double Swing Out Type
    A
    except Double Swing Out Type
    B



B
Go to step 6
A


5. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - MAIN BODY ECU AND BODY GROUND)

  1. Disconnect the 2C ECU connector.E233675E03

  1. for LH:

    1. Disconnect the n1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - n1-5 (TL)
      Always
      Below 1 Ω
      n1-4 (E) - Body ground
      n1-5 (TL) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the Y1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - Y1-5 (TL)
      Always
      Below 1 Ω
      Y1-6 (E) - Body ground
      Y1-5 (TL) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

6. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - MAIN BODY ECU AND BODY GROUND)

  1. Disconnect the 2C ECU connector.E157358E03

  1. for LH:

    1. Disconnect the K4 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - K4-6 (TL)
      Always
      Below 1 Ω
      K4-3 (E) - Body ground
      K4-6 (TL) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the L3 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - L3-6 (TL)
      Always
      Below 1 Ω
      L3-3 (E) - Body ground
      L3-6 (TL) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (REAR LIGHT - MAIN BODY ECU AND BODY GROUND)

  1. Disconnect the 2C ECU connector.E234112E02

  1. for LH:

    1. Disconnect the S11 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - S11-3
      Always
      Below 1 Ω
      S11-1 - Body ground
      S11-3 - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the S12 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - S12-3
      Always
      Below 1 Ω
      S12-1 - Body ground
      S12-3 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Taillight Circuit (Sep 2011 – Dec 2011)Stop Light Circuit (Sep 2011 – Dec 2011) →