2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Stop Light Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the stop light switch is turned on, current flows to the stop lights to illuminate them.

WIRING DIAGRAM

E234444E04
E234445E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Operate the intelligent tester according to the display and select the "Data List".

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

OK:
On the intelligent tester screen, each item changes between ON and OFF according to above chart



NG
Go to step 18
OK


2. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BATTERY AND BODY GROUND)

  1. E157762E01
    Disconnect the A39 relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-6 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT SWITCH)

  1. E158423E03
    Disconnect the A30 stop light switch connector.

  1. Disconnect the A39 relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A30-1 - A39-2 (STP)
    Always
    Below 1 Ω
    A30-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    w/ VSC
    A
    w/o VSC
    B



B
Go to step 15
A


5. INSPECT FUSE (ECU-IG No.2 FUSE)
  1. Remove the ECU-IG No.2 fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No.2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


6. INSPECT BRAKE LIGHT RELAY (BRK LP RELAY)

  1. E157759E01
    Remove the brake light relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω
    3 - 4
    Battery voltage not applied to terminals 1 and 2
    Below 1 Ω
    Battery voltage applied to terminals 1 and 2
    10 kΩ or higher



NG
REPLACE BRAKE LIGHT RELAY (BRK LP RELAY) (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BRAKE LIGHT RELAY)

  1. Remove the brake light relay from the engine room relay block.E160903E01

  1. Disconnect the A39 stop light control relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-8 (OUT) - Brake light relay terminal 4
    Always
    Below 1 Ω
    A39-6 (+B) - Brake light relay terminal 5
    A39-8 (OUT) - Body ground
    Always
    10 kΩ or higher
    A39-6 (+B) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - BATTERY)

  1. E160904E01
    Remove the brake light relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Brake light relay terminal 1 - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - SKID CONTROL ECU)

  1. Remove the brake light relay from the engine room relay block.E160905E02

  1. Disconnect the A24 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Brake light relay terminal 2 - A24-16 (STPO)
    Always
    Below 1 Ω
    Brake light relay terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    for Double Swing Out Type
    A
    except Double Swing Out Type
    B



B
Go to step 13
A


11. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - STOP LIGHT AND BODY GROUND)

  1. Remove the brake light relay from the engine room relay block.E234369E05

  1. for LH:

    1. Disconnect the n1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Brake light relay terminal 3 - n1-2 (STP)
      Always
      Below 1 Ω
      n1-4 (E) - Body ground
      n1-2 (STP) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the Y1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Brake light relay terminal 3 - Y1-2 (STP)
      Always
      Below 1 Ω
      Y1-6 (E) - Body ground
      Y1-2 (STP) - Body ground
      Always
      10 kΩ or higher

  1. Disconnect the T1 light connector.E160907E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Brake light relay terminal 3 - T1-1 (B)
    Always
    Below 1 Ω
    T1-2 (E) - Body ground
    T1-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. CHECK STOP LIGHT CONTROL RELAY ASSEMBLY
  1. Temporarily replace the stop light control relay with a new or normally functioning one.

  1. Check the stop light operation.

    OK:
    Stop light operation is normal.



NG
REPLACE SKID CONTROL ECU (Click here)
OK

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)

13. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - STOP LIGHT AND BODY GROUND)

  1. Remove the brake light relay from the engine room relay block.E160906E08

  1. for LH:

    1. Disconnect the K4 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Brake light relay terminal 3 - K4-5 (STP)
      Always
      Below 1 Ω
      K4-3 (E) - Body ground
      K4-5 (STP) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the L3 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Brake light relay terminal 3 - L3-5 (STP)
      Always
      Below 1 Ω
      L3-3 (E) - Body ground
      L3-5 (STP) - Body ground
      Always
      10 kΩ or higher

  1. Disconnect the S4 light connector.E160907E05

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Brake light relay terminal 3 - S4-1 (B)
    Always
    Below 1 Ω
    S4-2 (E) - Body ground
    S4-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. CHECK STOP LIGHT CONTROL RELAY ASSEMBLY
  1. Temporarily replace the stop light control relay with a new or normally functioning one.

  1. Check the stop light operation.

    OK:
    Stop light operation is normal.



NG
REPLACE SKID CONTROL ECU
OK

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)

15. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    for Double Swing Out Type
    A
    except Double Swing Out Type
    B



B
Go to step 17
A


16. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT AND BODY GROUND)

  1. Disconnect the A39 stop light control relay connector.E234375E01

  1. for LH:

    1. Disconnect the n1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A39-8 (OUT) - n1-2 (STP)
      Always
      Below 1 Ω
      n1-4 (E) - Body ground
      n1-2 (STP) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the Y1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A39-8 (OUT) - Y1-2 (STP)
      Always
      Below 1 Ω
      Y1-6 (E) - Body ground
      Y1-2 (STP) - Body ground
      Always
      10 kΩ or higher

  1. Disconnect the T1 light connector.E234376E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-8 (OUT) - T1-1 (B)
    Always
    Below 1 Ω
    T1-2 (E) - Body ground
    T1-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)

17. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT AND BODY GROUND)

  1. Disconnect the A39 stop light control relay connector.E234377E01

  1. for LH:

    1. Disconnect the K4 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A39-8 (OUT) - K4-5 (STP)
      Always
      Below 1 Ω
      K4-3 (E) - Body ground
      K4-5 (STP) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the L3 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A39-8 (OUT) - L3-5 (STP)
      Always
      Below 1 Ω
      L3-3 (E) - Body ground
      L3-5 (STP) - Body ground
      Always
      10 kΩ or higher

  1. Disconnect the S4 light connector.E234376E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-8 (OUT) - S4-1 (B)
    Always
    Below 1 Ω
    S4-2 (E) - Body ground
    S4-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)

18. INSPECT FUSE (STOP FUSE)
  1. Remove the STOP fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


19. INSPECT STOP LIGHT SWITCH

  1. E164228E01
    Remove the stop light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


20. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BODY GROUND)
E158513E01
  1. Disconnect the A30 stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A30-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


21. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STOP LIGHT SWITCH AND BATTERY)
E157769E01
  1. Disconnect the A30 stop light switch connector.

  1. Disconnect the 2B ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2B-22 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-22 (STP) - A30-1
    Always
    Below 1 Ω
    A30-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Taillight Circuit (from Jan 2012)Stop Light Circuit (from Jan 2012) →