B2785 Communication Malfunction between ECUs Connected by LIN
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The certification ECU (smart key ECU assembly) intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is output when a malfunction in the LIN communication bus between the components related to certification is detected continuously 3 times.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2785 |
The certification ECU (smart key ECU assembly) detects a malfunction in the LIN communication bus between components related to certification continuously 3 times. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the ignition switch off to troubleshoot:
- Connect intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- HINT:
- When DTC B2785 and B2287 are output simultaneously, perform the troubleshooting for DTC B2785 first.
| 1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - MASTER SWITCH) |
Disconnect the 2D and E29 ECU connectors.

Measure the resistance and voltage according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E29-10 (LIN) - 2D-20 (LIN1)
Always
Below 1 Ω
E29-10 (LIN) - Body ground
Always
10 kΩ or higher
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E29-10 (LIN) - Body ground
Always
Below 1 V
|
|
||||
| OK | |
| 2. CHECK FOR DTC |
Reconnect the E26 and E29 ECU connectors.
Reconnect the E28 box connector.
Clear the DTC (Click here).
Recheck for DTCs.
Result Result
Proceed to
DTC B2785 is output
A
DTC B2785 is not output
B
|
|
||||
| A | |
| 3. CHECK FOR DTC |
Reconnect the 2D ECU connector.
Disconnect the E26 ECU connector.
Clear the DTC (Click here).
Recheck for DTCs.
Result Result
Proceed to
DTC B2785 is output
A
DTC B2785 is not output
B
|
|
||||
| A | |
| 4. CHECK FOR DTC |
Reconnect the E26 ECU connector.
Disconnect the E28 box ECU connector.
Clear the DTC (Click here).
Recheck for DTCs.
Result Result
Proceed to
DTC B2785 is output
A
DTC B2785 is not output
B
|
|
||||
| A | ||
| ||
| 5. REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |
Temporarily replace the main body ECU (cowl side junction block LH) with a new or normally functioning one.
Clear the DTC (Click here).
| NEXT | |
| 6. CHECK FOR DTC |
Recheck for DTCs.
Result Result
Proceed to
DTC B2785 is not output
A
DTC B2785 is output
B
|
|
||||
| A | ||
| ||
| 7. REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |
Temporarily replace the steering lock ECU with a new or normally functioning one (Click here).
Clear the DTC (Click here).
| NEXT | |
| 8. CHECK FOR DTC |
Recheck for DTCs.
Result Result
Proceed to
DTC B2785 is not output
A
DTC B2785 is output
B
|
|
||||
| A | ||
| ||
| 9. REPLACE ID CODE BOX (IMMOBILISER CODE ECU) |
Temporarily replace the ID code box immobiliser code ECU with a new or normally functioning one.
Clear the DTC (Click here).
| NEXT | |
| 10. CHECK FOR DTC |
Recheck for DTCs (Click here).
Result Result
Proceed to
DTC B2785 is not output
A
DTC B2785 is output
B
|
|
||||
| A | ||
| ||
