2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

SYSTEM DESCRIPTION

This circuit detects the conditions of the mirror retract switch.
The outer mirror switch sends information about the operating condition of the mirror retract switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU.

WIRING DIAGRAM

B188307E03

INSPECTION PROCEDURE


1. CHECK DTC
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output (for LHD)
    B
    CAN DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (MIRROR RETRACT SWITCH)
  1. Check the Data List for proper functioning of the mirror retract switch (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Outer Mirror Fold SW
    Mirror retract switch signal / ON or OFF
    ON: Switch is on (retracting)
    OFF: Switch is off
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MIRROR RETRACT FUNCTION)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power mirror control function (Click here).

    Mirror 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Mirror Fold
    Mirror retract operation
    FOLD / OFF
    -
    Mirror Return
    Mirror retract operation
    RETURN / OFF
    -
    Result 
    Result
    Proceed to
    Outer rear view mirror operates normally
    A
    Outer rear view mirror LH does not operate normally
    B
    Outer rear view mirror RH does not operate normally
    C



B
Go to step 6

C
Go to step 8
A

REPLACE OUTER MIRROR CONTROL ECU (Click here)

4. INSPECT OUTER MIRROR SWITCH ASSEMBLY (RETRACTABLE OUTER MIRROR SWITCH)

  1. B183740E01
    Remove the switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (E) - 3 (MR)
    Pressed (Retracts)
    Below 1 Ω
    Not pressed
    10 kΩ or higher



NG
REPLACE RETRACTABLE OUTER MIRROR SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU AND BODY GROUND)

  1. B183741E01
    Disconnect the E2 ECU connector.

  1. Disconnect the G2 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-6 (RET) - G2-3 (MR)
    Always
    Below 1 Ω
    G2-2 (E) - Body ground
    G2-3 (MR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

6. INSPECT OUTER MIRROR RETRACTOR LH

  1. B181043E01
    Remove the mirror LH (Click here).

  1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    NOTICE:
    1. Disconnect and reconnect the battery once between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Forward position (A)
    Moves from (A) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Forward position (A)
    Does not move
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to forward position (A)
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Driving position (C)
    Moves from (C) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Driving position (C)
    Does not move
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to driving position (C)
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Retracted position (E)
    Does not move
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Retracted position (E)
    Moves from (E) to driving position (C)



NG
REPLACE OUTER MIRROR RETRACTOR LH (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)

  1. B183742E03
    for LHD:
    1. Disconnect the I17 ECU connector.

    2. Disconnect the I15 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I17-1 (RL) - I15-15 (MR)
      Always
      Below 1 Ω
      I17-2 (FL) - I15-16 (MF)
      I15-15 (MR) - Body ground
      Always
      10 kΩ or higher
      I15-16 (MF) - Body ground

  1. for RHD:

    1. Disconnect the I23 ECU connector.

    2. Disconnect the I15 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I23-1 (RL) - I15-15 (MR)
      Always
      Below 1 Ω
      23-2 (FL) - I15-16 (MF)
      I15-15 (MR) - Body ground
      Always
      10 kΩ or higher
      I15-16 (MF) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)

8. INSPECT OUTER MIRROR RETRACTOR RH

  1. B181044E01
    Remove the mirror RH (Click here).

  1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    NOTICE:
    1. Disconnect and reconnect the battery once between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Forward position (A)
    Moves from (A) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Forward position (A)
    Does not move
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to forward position (A)
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Driving position (C)
    Moves from (C) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Driving position (C)
    Does not move
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to retracted position (E)
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to driving position (C)
    Battery positive (+) → Terminal 15 (MR)
    Battery negative (-) → Terminal 16 (MF)
    Retracted position (E)
    Does not move
    Battery negative (-) → Terminal 15 (MR)
    Battery positive (+) → Terminal 16 (MF)
    Retracted position (E)
    Moves from (E) to driving position (C)



NG
REPLACE OUTER MIRROR RETRACTOR RH (Click here)
OK


9. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)

  1. B183742E06
    for LHD:
    1. Disconnect the I17 ECU connector.

    2. Disconnect the I7 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I17-5 (RR) - I7-15 (MR)
      Always
      Below 1 Ω
      I17-6 (FR) - I7-16 (MF)
      I7-15 (MR) - Body ground
      Always
      10 kΩ or higher
      I7-16 (MF) - Body ground

  1. for RHD:

    1. Disconnect the I23 ECU connector.

    2. Disconnect the I7 mirror connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I23-5 (RR) - I7-15 (MR)
      Always
      Below 1 Ω
      I23-6 (FR) - I7-16 (MF)
      I7-15 (MR) - Body ground
      Always
      10 kΩ or higher
      I7-16 (MF) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)


← Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch (from Jan 2012)Power Retractable Mirrors do not Operate with Power Retract Mirror Switch (from Jan 2012) →