OPERATION CHECK
Troubleshooting · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| INSPECT INDICATOR/WARNING LIGHT |
Check the following indicators and warning lights.
w/o Multi-information Display Indicator/Warning Light
Switch Condition
Specified Condition
A/T OIL TEMP warning light*1
Ignition switch off → ON
Comes on for 3 seconds
BRAKE warning light
ABS warning light
OIL LEVEL indicator light
FUEL FILTER & SEDIMENTER indicator light*2
SLIP indicator light*3
VSC OFF indicator light*3
WASHER indicator light
RSCA OFF indicator light*4
CRAWL indicator light*3
SPEED LIMIT indicator light
Eco driving indicator light
TRC OFF indicator light*3
Turn assist indicator light*3
Multi-terrain select indicator light*5
SRS warning light
Ignition switch off → ON
Comes on for 6 seconds
CHARGE warning light
Ignition switch off → ON
Illuminates when ignition switch is turned ON. Turns off when engine is started.
MIL
- *1: for Automatic Transmission
- *2: for 1VD-FTV
- *3: w/ VSC
- *4: w/ Curtain Shield Airbag
- *5: w/ Multi-terrain Select
- *1: for Automatic Transmission
| Indicator/Warning Light |
Switch Condition |
Specified Condition |
| BRAKE warning light |
Ignition switch off → ON |
Comes on for 3 seconds |
| ABS warning light | ||
| SLIP indicator light | ||
| RSCA OFF indicator light*1 | ||
| CRAWL indicator light | ||
| SPEED LIMIT indicator light | ||
| PCS indicator light*2 | ||
| Eco driving indicator light | ||
| VSC OFF indicator light | ||
| Turn assist indicator light | ||
| Multi-terrain select indicator light*4 | ||
| Headlight beam level control system warning light*3 | ||
| SRS warning light |
Ignition switch off → ON |
Comes on for 6 seconds |
| CHARGE warning light |
Ignition switch off → ON |
Illuminates when ignition switch is turned ON. Turns off when engine is started. |
| MIL |
- *1: w/ Curtain Shield Airbag
- *2: w/ Pre-crash Safety System
- *3: w/ Headlight Leveling
- *4: w/ Multi-terrain Select
| INSPECT SPEEDOMETER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
- Reference:
mph Standard Indication
Acceptable Range
20 mph
18.5 to 22 mph
40 mph
39.5 to 42.5 mph
60 mph
59.5 to 63 mph
80 mph
80.5 to 84.5 mph
100 mph
100.5 to 105.5 mph
120 mph
119.5 to 126 mph
140 mph
141 to 147 mph
km/h (except Australia) Standard Indication
Acceptable Range
20 km/h
21 to 25 km/h
40 km/h
41.7 to 46.2 km/h
60 km/h
62.7 to 67.2 km/h
80 km/h
83.4 to 88.4 km/h
100 km/h
104.3 to 109.3 km/h
120 km/h
125.1 to 130.6 km/h
140 km/h
145.8 to 151.8 km/h
160 km/h
166.2 to 173.2 km/h
180 km/h
186.9 to 194.5 km/h
200 km/h
207.7 to 215.7 km/h
220 km/h
228.4 to 236.8 km/h
240 km/h
249.2 to 258 km/h
km/h (for Australia) Standard Indication
Acceptable Range
20 km/h
17.5 to 21.5 km/h
40 km/h
38 to 42 km/h
60 km/h
58 to 63 km/h
80 km/h
78 to 84 km/h
100 km/h
98.5 to 104.5 km/h
120 km/h
119 to 125 km/h
140 km/h
139 to 146 km/h
160 km/h
159 to 167 km/h
180 km/h
186.9 to 194.5 km/h
200 km/h
199 to 209 km/h
220 km/h
219 to 230 km/h
240 km/h
239 to 251 km/h
- NOTICE:
- Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.
Check the deflection width of the speedometer indicator.
- Reference:
- Within 0.3°
| INSPECT TACHOMETER |
Connect a tune-up tachometer, and start the engine.
Compare the test results with the tachometer indicator.
- DC 13.5 V, at 25°C (77°F):
Standard indication (rpm)
Acceptable range
Data in ( ) is for reference
700
630 to 770
1000
(900 to 1100)
2000
(1850 to 2150)
3000
2800 to 3200
4000
(3800 to 4200)
5000
4800 to 5200
6000
(5750 to 6250)
| INSPECT METER/GAUGE |
Connect the intelligent tester to the DLC3.
Perform Active Test (Click here).
- OK:
- Each meter/gauge needle indication is normal.
| INSPECT WARNING/INDICATOR LIGHT |
Connect the intelligent tester to the DLC3.
Perform Active Test (Click here).
- OK:
- Each warning/indicator light turns on and off using the intelligent tester.
| INSPECT ENGINE OIL LEVEL WARNING (except for 3UR-FE) |
Turn the ignition switch to ON and warm up the engine at an engine speed of 2000 rpm or less until the coolant temperature reaches approximately 80°C (176°F) or more.
Disconnect the engine oil level sensor connector for 40 seconds or more.
Turn the ignition switch to ON and check the multi-information display.
- OK:
- Low engine oil level message is displayed.
| INSPECT MULTI-INFORMATION DISPLAY (w/ Multi-information Display) |
Connect the intelligent tester to the DLC3.
Perform Active Test (Click here).
- HINT:
- If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end Active Test and turn the ignition switch off.
- OK:
- All dots in the multi-information display turn on and off using the intelligent tester.