2011-2013 Land Cruiser · Service Manual Vehicle Interior

Meter Illumination does not Dim at Night

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

w/ Multi-information Display:
If the dimmer switch is turned to TAIL, HEAD or AUTO, the main body ECU sends a TAIL relay signal, panel light illumination signal, panel relay signal, and TAIL cancel switch off signal to the combination meter. Then the meter and accessory meter become dim.

HINT:
TAIL cancel switch: When the headlights are illuminated and the TAIL cancel switch is turned on, the meter does not dim.


WIRING DIAGRAM

E156914E04

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    CAN communication system DTC is not output
    A
    CAN communication system (for LHD) DTC is output
    B
    CAN communication system (for RHD) DTC is output
    C



B
Go to CAN COMMUNICATION SYSTEM (Click here)

C
Go to CAN COMMUNICATION SYSTEM (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (LIGHT CONTROL RHEOSTAT)
  1. Operate the intelligent tester according to the display and select Data List (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tail Cancel SW*
    TAIL cancel switch condition/ON or OFF
    ON: TAIL cancel switch ON
    OFF: TAIL cancel switch OFF
    -
    Rheostat value
    Light control rheostat switch input/Min.: 0, Max.: 100
    Light control rheostat switch is fully turned right (0) → fully turned left (100)
    Unit: %

    HINT:
    *: w/ TAIL Cancel Switch

    OK:
    Light brightness can be changed within specified range by manual operation.



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

3. INSPECT LIGHT CONTROL RHEOSTAT

  1. Inspect the light control rheostat.E154786E04

    1. Remove the light control rheostat (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (TC) - 1 (E)
      TAIL cancel switch off → on
      10 kΩ or higher → Below 1 Ω
      5 (T) - 1 (E)
      Always
      10 kΩ or higher
      7 (TR) - 1 (E)
      Light control rheostat fully turned right → fully turned left
      10 kΩ or higher → Below 100 Ω

  1. Inspect the trip switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 (A/B) - 1 (E)
      TRIP switch on (Pushed)
      Below 200 Ω
      TRIP switch off (Not Pushed)
      1 MΩ or higher



NG
REPLACE LIGHT CONTROL RHEOSTAT (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT)

  1. E156954E06
    Disconnect the E8 meter connector.

  1. Disconnect the E9 rheostat connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-18 (ILL+) - E9-5 (T)
    Always
    Below 1 Ω
    E8-19 (TR) - E9-7 (TR)
    E8-23 (E2) - E9-1 (E)
    E8-20 (TC) - E9-6 (TC)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Meter Illumination is Always Dark (from Jan 2012)Meter Illumination does not Dim at Night (from Jan 2012) →