2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Turn Signal Light Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The turn signal flasher receives a turn signal switch signal from the headlight dimmer switch, and illuminates the front turn signal light, outer rear view mirror and rear combination light.

WIRING DIAGRAM

E234331E02

INSPECTION PROCEDURE


1. CHECK TURN SIGNAL LIGHT FUNCTION
  1. Check that the turn signal lights blink.

    Result 
    Result
    Proceed to
    All turn signal lights do not blink
    A
    Only front turn signal light does not blink
    B
    Only rear combination light does not blink
    C
    Only side turn signal light does not blink
    D



B
Go to step 4

C
Go to step 5

D
Go to step 8
A


2. INSPECT FUSE (LH-IG, TURN-HAZ FUSE)
  1. Remove the LH-IG fuse from the main body ECU.

  1. Remove the TURN-HAZ fuse from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LH-IG fuse
    Always
    Below 1 Ω
    TURN-HAZ fuse



NG
REPLACE FUSE
OK


3. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER - BATTERY AND BODY GROUND)

  1. E157336E01
    Disconnect the E19 turn signal flasher connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E19-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    E19-4 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E19-7 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. CHECK HARNESS AND CONNECTOR (HEADLIGHT - TURN SIGNAL FLASHER AND BODY GROUND)

  1. E157337E01
    Disconnect the E19 turn signal flasher connector.

  1. for LH:

    1. Disconnect the A1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A1-6 (B) - E19-3 (LL)
      Always
      Below 1 Ω
      A1-3 (E) - Body ground
      A1-6 (B) - Body ground
      Always
      10 kΩ or higher

  1. E157337E02
    for RH:
    1. Disconnect the A10 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A10-6 (B) - E19-2 (LR)
      Always
      Below 1 Ω
      A10-3 (E) - Body ground
      A10-6 (B) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

5. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    for Double Swing Out Type
    A
    except Double Swing Out Type
    B



B
Go to step 7
A


6. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL FLASHER AND BODY GROUND)

  1. E157337E06
    Disconnect the E19 turn signal flasher connector.

  1. for LH:

    1. Disconnect the n1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      n1-1 (TRN) - E19-3 (LL)
      Always
      Below 1 Ω
      n1-4 (E) - Body ground
      n1-1 (TRN) - Body ground
      Always
      10 kΩ or higher

  1. E157337E07
    for RH:
    1. Disconnect the Y1 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Y1-3 (TRN) - E19-2 (LR)
      Always
      Below 1 Ω
      Y1-6 (E) - Body ground
      Y1-3 (TRN) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

7. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL FLASHER AND BODY GROUND)

  1. E157338E01
    Disconnect the E19 turn signal flasher connector.

  1. for LH:

    1. Disconnect the K4 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K4-4 (TRN) - E19-3 (LL)
      Always
      Below 1 Ω
      K4-3 (E) - Body ground
      K4-4 (TRN) - Body ground
      Always
      10 kΩ or higher

  1. E157338E02
    for RH:
    1. Disconnect the L3 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L3-4 (TRN) - E19-2 (LR)
      Always
      Below 1 Ω
      L3-3 (E) - Body ground
      L3-4 (TRN) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

8. CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT - TURN SIGNAL FLASHER AND BODY GROUND)

  1. E159513E05
    Disconnect the E19 turn signal flasher connector.

  1. for LH:

    1. Disconnect the A45 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for Double Swing Out Type: 
      Tester Connection
      Condition
      Specified Condition
      A45-1 - E19-3 (LL)
      Always
      Below 1 Ω
      A45-2 - Body ground
      A45-1 - Body ground
      Always
      10 kΩ or higher
      except Double Swing Out Type: 
      Tester Connection
      Condition
      Specified Condition
      A45-2 - E19-3 (LL)
      Always
      Below 1 Ω
      A45-1 - Body ground
      A45-2 - Body ground
      Always
      10 kΩ or higher

  1. E159513E06
    for RH:
    1. Disconnect the A47 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for Double Swing Out Type: 
      Tester Connection
      Condition
      Specified Condition
      A47-1 - E19-2 (LR)
      Always
      Below 1 Ω
      A47-2 - Body ground
      A47-1 - Body ground
      Always
      10 kΩ or higher
      except Double Swing Out Type: 
      Tester Connection
      Condition
      Specified Condition
      A47-2 - E19-2 (LR)
      Always
      Below 1 Ω
      A47-1 - Body ground
      A47-2 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Rear Fog Light Circuit (from Jan 2012)Turn Signal Light Circuit (from Jan 2012) →