2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed between 3 settings.

WIRING DIAGRAM

Refer to DTC P0230 (Click here).

INSPECTION PROCEDURE

This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the Problem Symptoms Table (Click here).

1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL PUMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether operating sounds can be heard while operating the fuel pump using the tester.

    OK:
    Operating sounds can be heard from fuel pump.



NG
Go to step 5
OK


2. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
A179602E09
  1. Disconnect the N3 fuel pump ECU connector.

  1. Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N13-5 (FPC) - A38-52 (FPC)
    Always
    Below 1 Ω
    N13-4 (DI) - A38-18 (DI)
    Always
    Below 1 Ω
    N13-6 (E) - Body ground
    Always
    Below 1 Ω
    N13-1 (FP-) - Body ground
    Always
    10 kΩ or higher
    N13-5 (FPC) or A38-52 (FPC) - Body ground
    Always
    10 kΩ or higher
    N13-4 (DI) or A38-18 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


4. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END

5. INSPECT CIRCUIT OPENING RELAY (C/OPN)
  1. Inspect the circuit opening relay (C/OPN) (Click here).



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN)
OK


6. INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)
A162278E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C/OPN relay (2) - Body ground
    Engine switch on (IG)
    11 to 14 V
    C/OPN relay (5) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 13
OK


7. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - ECU, FUEL PUMP ECU)
A179603E05
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Disconnect the A38 ECM connector.

  1. Disconnect the N13 fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (1) - A38-48 (FC)
    Always
    Below 1 Ω
    C/OPN relay (3) - N13-3 (+B)
    Always
    Below 1 Ω
    C/OPN relay (1) or A38-48 (FC) - Body ground
    Always
    10 kΩ or higher
    C/OPN relay (3) or N13-3 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
A179604E05
  1. Disconnect the N1 fuel pump connector.

  1. Disconnect the N13 fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N1-4 (B2) - N13-2 (FP)
    Always
    Below 1 Ω
    N1-5 (E2) - N13-1 (FP-)
    Always
    Below 1 Ω
    N1-4 (B2) or N13-2 (FP) - Body ground
    Always
    10 kΩ or higher
    N1-5 (E2) or N13-1 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
A179602E11
  1. Disconnect the N13 fuel pump ECU connector.

  1. Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N13-5 (FPC) - A38-52 (FPC)
    Always
    Below 1 Ω
    N13-4 (DI) - A38-18 (DI)
    Always
    Below 1 Ω
    N13-6 (E) - Body ground
    Always
    Below 1 Ω
    N13-5 (FPC) or A38-52 (FPC) - Body ground
    Always
    10 kΩ or higher
    N13-4 (DI) or A38-18 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END

13. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - EFI NO. 2 RELAY, IGN FUSE)
A180108E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Remove the EFI NO. 2 relay (EFI NO. 2) from the engine room relay block.

  1. Remove the IGN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (2) - IGN fuse (2)
    Always
    Below 1 Ω
    C/OPN relay (5) - EFI NO. 2 relay (3)
    Always
    Below 1 Ω
    C/OPN relay (2) or IGN fuse (2) - Body ground
    Always
    10 kΩ or higher
    C/OPN relay (5) or EFI NO. 2 relay (3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. INSPECT EFI NO. 2 RELAY (EFI NO. 2)
  1. Inspect the EFI NO. 2 relay (EFI NO. 2) (Click here).



NG
REPLACE EFI NO. 2 RELAY (EFI NO. 2)
OK


15. CHECK HARNESS AND CONNECTOR (EFI NO. 2 RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND)
A180643E02
  1. Remove the EFI MAIN 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI MAIN 2 fuse
    Always
    Below 1 Ω

  1. Reinstall the EFI MAIN 2 fuse.

  1. Remove the EFI NO. 2 relay (EFI NO. 2) from the engine room relay block.

  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the 1B integration relay connector.

  1. Disconnect the cable from the battery positive (+) terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 2 relay (1) - 1B-4
    Always
    Below 1 Ω
    EFI NO. 2 relay (5) - Positive (+) battery cable
    Always
    Below 1 Ω
    EFI NO. 2 relay (2) - Body ground
    Always
    Below 1 Ω
    EFI NO. 2 relay (1) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    EFI NO. 2 relay (5) or Positive (+) battery cable - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)


← VC Output Circuit (from Jan 2012)Fuel Pump Control Circuit (from Jan 2012) →