Home › Engine / Hybrid / EV System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
Fuel Pump Control Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1. PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether operating sounds can be heard while operating the fuel pump using the GTS.
OK:
Operating sounds can be heard from fuel pump.
Result
Result
Proceed to
NG
A
OK
B
B
A
2. INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE)
Disconnect the fuel pump ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
N14-6 (+B) - Body Ground
Ignition switch ON
11 to 14 V
Text in Illustration
*a
Front view of wire harness connector (to Fuel Pump ECU)
NG
OK
3. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - BODY GROUND)
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
N14-3 (E) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
4. CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
Disconnect the fuel pump connector.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
N1-4 (B2) - N14-1 (FP)
Always
Below 1 Ω
N1-5 (E2) - N14-2 (FP-)
Always
Below 1 Ω
N1-4 (B2) or N14-1 (FP) - Body ground
Always
10 kΩ or higher
N1-5 (E2) or N14-2 (FP-) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. INSPECT FUEL PUMP
Inspect the fuel pump (Click here ).
NG
OK
6. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for LHD
Tester Connection
Condition
Specified Condition
N14-5 (FPC) - A38-52 (FPC)
Always
Below 1 Ω
N14-5 (FPC) or A38-52 (FPC) - Body ground
Always
10 kΩ or higher
for RHD
Tester Connection
Condition
Specified Condition
N14-5 (FPC) - A52-52 (FPC)
Always
Below 1 Ω
N14-5 (FPC) or A52-52 (FPC) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
7. REPLACE FUEL PUMP ECU
Replace the fuel pump ECU (Click here ).
NEXT
8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Check the fuel pump operation.
OK:
Malfunction has been repaired successfully.
NG
OK
9. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - FUEL PUMP ECU)
Remove the integration relay from the engine room relay block.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
1B-4 - N14-6 (+B)
Always
Below 1 Ω
1B-4 or N14-6 (+B) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
10. PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)
Remove the fuel tank assembly (Click here ).
Remove the fuel pump from the fuel tank assembly.
Clean the fuel pump to completely remove any remaining fuel.
Connect the fuel pump connector.
CAUTION:
Make sure that there is no fuel remaining inside or on the outside of the fuel pump.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.
Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
GTS Operation
Specified Condition
1 - 2
FPC Duty: 25%
3.2 to 4.05 V
FPC Duty: 80%
8.8 to 12.5 V
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
GTS Operation
Specified Condition
1 - 2
ON (FPC Duty: 90%)
9.0 to 14.0 V
HINT:
Be sure to measure the voltage with all the connectors connected.
Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).
Text in Illustration
*a
Component with harness connected (Fuel Pump)
NG
OK
11. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for LHD
Tester Connection
Condition
Specified Condition
N14-5 (FPC) - A38-52 (FPC)
Always
Below 1 Ω
N14-5 (FPC) or A38-52 (FPC) - Body ground
Always
10 kΩ or higher
for RHD
Tester Connection
Condition
Specified Condition
N14-5 (FPC) - A52-52 (FPC)
Always
Below 1 Ω
N14-5 (FPC) or A52-52 (FPC) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
12. REPLACE FUEL PUMP
Replace the fuel pump (Click here ).
NEXT
13. REPLACE FUEL PUMP ECU
Replace the fuel pump ECU (Click here ).
NEXT
14. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Check the fuel pump operation.
OK:
Malfunction has been repaired successfully.
NG
OK