Home › Engine / Hybrid / EV System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
ECM Power Source Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When the ignition switch is turned to ON, battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to either terminal +B or +B2 of the ECM. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BATTERY)
Remove the integration relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
1C-1 - Body ground
Always
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
2. INSPECT INTEGRATION RELAY (EFI RELAY AND IG2 RELAY)
Inspect the integration relay (Click here ).
NG
REPLACE INTEGRATION RELAY
OK
3. CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
Check the harness and the connectors between the integration relay and the ECM.
Remove the integration relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for LHD
Tester Connection
Condition
Specified Condition
A38-34 (MREL) - 1B-2
Always
Below 1 Ω
A38-3 (+B) - 1B-4
Always
Below 1 Ω
A38-2 (+B2) - 1B-4
Always
Below 1 Ω
A38-34 (MREL) or 1B-2 - Body ground
Always
10 kΩ or higher
A38-3 (+B) or 1B-4 - Body ground
Always
10 kΩ or higher
A38-2 (+B2) or 1B-4 - Body ground
Always
10 kΩ or higher
for RHD
Tester Connection
Condition
Specified Condition
A52-34 (MREL) - 1B-2
Always
Below 1 Ω
A52-3 (+B) - 1B-4
Always
Below 1 Ω
A52-2 (+B2) - 1B-4
Always
Below 1 Ω
A52-34 (MREL) or 1B-2 - Body ground
Always
10 kΩ or higher
A52-3 (+B) or 1B-4 - Body ground
Always
10 kΩ or higher
A52-2 (+B2) or 1B-4 - Body ground
Always
10 kΩ or higher
Check the harness and connectors between the integration relay and body ground.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
1B-3 - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for LHD
Tester Connection
Condition
Specified Condition
C45-81 (E1) - Body ground
Always
Below 1 Ω
for RHD
Tester Connection
Condition
Specified Condition
C46-81 (E1) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. INSPECT ECM (IGSW VOLTAGE)
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
for LHD
Tester Connection
Switch Condition
Specified Condition
A38-28 (IGSW) - C45-81 (E1)
Ignition switch ON
11 to 14 V
for RHD
Tester Connection
Switch Condition
Specified Condition
A52-28 (IGSW) - C46-81 (E1)
Ignition switch ON
11 to 14 V
NG
OK
6. INSPECT FUSE (IGN)
Remove the IGN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance :
Tester Connection
Condition
Specified Condition
IGN fuse
Always
Below 1 Ω
NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK
7. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
Remove the integration relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for LHD
Tester Connection
Condition
Specified Condition
1B-8 - A38-28 (IGSW)
Always
Below 1 Ω
1B-8 or A38-28 (IGSW) - Body ground
Always
10 kΩ or higher
for RHD
Tester Connection
Condition
Specified Condition
1B-8 - A52-28 (IGSW)
Always
Below 1 Ω
1B-8 or A52-28 (IGSW) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
8. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
Result
Result
Proceed to
w/ Entry and Start System
A
w/o Entry and Start System
B
B
A
9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE ROOM RELAY BLOCK)
Remove the integration relay from the engine room relay block.
Disconnect the E2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
E2-11 (IG2D) - 1B-6
Always
Below 1 Ω
E2-11 (IG2D) or 1B-6 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
10. CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)
Check the entry and start system (Click here ).
NG
OK
11. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM RELAY BLOCK)
Remove the integration relay from the engine room relay block.
Disconnect the E93 ignition switch connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
E93-6 (IG2) - 1B-6
Always
Below 1 Ω
1B-7 - Body ground
Always
Below 1 Ω
E93-6 (IG2) or 1B-6 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
12. INSPECT IGNITION SWITCH ASSEMBLY
Inspect the ignition switch assembly (Click here ).
NG
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)