2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A274415E01
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Grommet
    *2
    Pin
    *3
    Hook
    *4
    Bracket


5. REMOVE AIR CLEANER CAP AND HOSE

  1. A272589
    Disconnect the No. 2 PCV hose and No. 1 air hose.

  1. Disconnect the mass air flow meter connector and detach the clamp.

  1. Detach the 4 clamps.

  1. Loosen the hose clamp and remove the air cleaner cap and hose.


6. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


7. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


8. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover sub-assembly.


9. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the 2 cylinder block drain cock plugs and drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

    A266163E01

    Text in Illustration 
    *1
    Reservoir Cap
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


10. REMOVE NO. 5 WATER BY-PASS PIPE

  1. A268559
    Disconnect the 2 water by-pass hoses and remove the 2 bolts and No. 5 water by-pass pipe.


11. REMOVE EGR VALVE BRACKET

  1. A268560
    Detach the 2 wire harness clamps and PCV hose clamp.

  1. Remove the 3 bolts and EGR valve bracket.


12. REMOVE PCV HOSE ASSEMBLY

  1. A268558
    Disconnect the PCV hose from the PCV pipe of the cylinder head cover LH and RH.

  1. Remove the bolt and PCV hose.


13. REMOVE AIR TUBE SUB-ASSEMBLY (w/ Secondary Air Injection System)

  1. A272661
    Disconnect the No. 2 air injection system hose from the air switching valve.

  1. A271405
    Disconnect the manifold absolute pressure sensor connector and detach the clamp.

  1. Remove the 2 bolts and bracket.

  1. A218662
    Remove the bolt and air tube.


14. REMOVE INTAKE MANIFOLD

  1. w/o Secondary Air Injection System:

    1. A271404
      Disconnect the manifold absolute pressure sensor connector and detach the clamp.

    2. Remove the 2 bolts and bracket.

  1. A215281
    Disconnect the No. 4 water by-pass hose.

  1. Disconnect the throttle position sensor and throttle control motor connector.

  1. Disconnect the PCV valve hose.

  1. A230824
    Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.

  1. Disconnect the vacuum switching valve connector (for ACIS).

  1. A271406
    Remove the bolt.

  1. Detach the 3 wire harness clamps from the 3 wire harness brackets.

  1. A218653
    Disconnect the fuel tube from the fuel delivery pipe (Click here).

  1. A218654
    Disconnect the fuel tube from the No. 2 fuel delivery pipe (Click here).

  1. A230830
    Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut


15. REMOVE FUEL TUBE SUB-ASSEMBLY

  1. A218656
    Remove the bolt and fuel tube from the intake manifold.


16. REMOVE BRACKET

  1. A218660
    Remove the 2 bolts and 2 brackets.


17. REMOVE V-BANK COVER BRACKET

  1. A215290
    Remove the 2 bolts and V-bank cover bracket.


18. REMOVE V-BANK COVER PIN

  1. A215291
    Remove the V-bank cover pin from the intake manifold.


19. REMOVE INTAKE FLANGE

  1. A268561
    Remove the 2 nuts and intake flange.


20. REMOVE STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.

  1. A230826
    Using an E5 "TORX" socket wrench, remove the 2 stud bolts.


21. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

  1. A218659E01
    Disconnect the 2 vacuum hoses and detach the 3 clamps.

  1. Remove the bolt and vacuum switching valve.


22. REMOVE PURGE VSV

  1. A215294
    Disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.


23. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR

  1. A272561
    Disconnect the manifold absolute pressure sensor connector.

  1. Remove the bolt and manifold absolute pressure sensor.


24. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

  1. A215292
    Remove the 4 bolts, throttle body with motor assembly and gasket.

← COMPONENTS (from Jan 2012)INSTALLATION (from Jan 2012) →