2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012


1. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A274415E01
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Grommet
    *2
    Pin
    *3
    Hook
    *4
    Bracket


2. REMOVE AIR CLEANER AND HOSE

  1. A271401
    Disconnect the No. 2 PCV hose and No. 1 air hose.

  1. Disconnect the mass air flow meter connector and detach the clamp.

  1. Remove the 3 bolts and loosen the hose clamp, and then remove the air cleaner and hose.


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover sub-assembly.


6. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


7. REMOVE FRONT FENDER APRON TRIM PACKING B

  1. A177004
    w/ KDSS:
    Remove the 3 clips and front fender apron trim packing B.

  1. A176301
    w/o KDSS:
    Remove the 4 clips and front fender apron trim packing B.


8. REMOVE FRONT FENDER APRON TRIM PACKING D

  1. A177005
    Remove the 4 clips and front fender apron trim packing D.


9. REMOVE FRONT FENDER APRON TRIM PACKING A

  1. A177003
    Remove the 3 clips and front fender apron trim packing A.


10. REMOVE FRONT FENDER APRON TRIM PACKING C

  1. A177002
    Remove the 4 clips and front fender apron trim packing C.


11. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)

13. REMOVE PROPELLER SHAFT HEAT INSULATOR

  1. A175007
    Remove the 2 bolts and heat insulator.


14. REMOVE NO. 2 MANIFOLD STAY

  1. A184508
    Remove the 3 bolts and No. 2 manifold stay.


15. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A218610
    Remove the 3 bolts and No. 2 exhaust manifold heat insulator.


16. REMOVE EXHAUST MANIFOLD ASSEMBLY LH

  1. A218609
    Disconnect the air fuel ratio sensor connector and detach the wire harness clamp.

  1. A268566E01
    w/ Secondary Air Injection System:
    Remove the 9 nuts, exhaust manifold and 2 gaskets.
    Text in Illustration 
    *A
    w/ Secondary Air Injection System
    *B
    w/o Secondary Air Injection System

  1. w/o Secondary Air Injection System:
    Remove the 7 nuts, exhaust manifold and gasket.


17. REMOVE MANIFOLD STAY

  1. A184511
    Remove the 3 bolts and manifold stay.


18. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A218612
    Remove the engine oil level dipstick.

  1. Detach the engine wire clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.


19. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A218614
    Remove the 3 bolts and heat insulator.


20. REMOVE EXHAUST MANIFOLD ASSEMBLY RH

  1. A218613
    Disconnect the air fuel ratio sensor connector and detach the wire harness clamp.

  1. A268567E01
    w/ Secondary Air Injection System:
    Remove the 9 nuts, exhaust manifold and 2 gaskets.
    Text in Illustration 
    *A
    w/ Secondary Air Injection System
    *B
    w/o Secondary Air Injection System

  1. w/o Secondary Air Injection System:
    Remove the 7 nuts, exhaust manifold and 2 gaskets.


21. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

  1. A218732E01
    Using SST, remove the air fuel ratio sensor from the exhaust manifold LH.
    SST
    09224-00010  


22. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

  1. A218733E01
    Using SST, remove the air fuel ratio sensor from the exhaust manifold RH.
    SST
    09224-00010  

← COMPONENTS (from Jan 2012)INSTALLATION (from Jan 2012) →