2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. Remove the 7 clips and radiator support seal.

    B180890E02


4. REMOVE RADIATOR GRILLE

B180899E01
  1. Put protective tape around the radiator grille.

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille.


5. REMOVE FRONT BUMPER COVER

HINT:
For the front bumper cover with garnish, use the procedures described below.

  1. Put protective tape around the bumper cover.

    B180993E01

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B180994E01

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Detach the 10 claws and remove the bumper cover.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Detach the 10 claws, disconnect the No. 4 engine room wire connector and remove the bumper cover.

    B180995

  1. B181927
    w/ Headlight Cleaner System:
    Disconnect the headlight cleaner hose and remove the bumper cover.


6. REMOVE TRANSMISSION OIL COOLER AIR DUCT

  1. A174154
    Remove the 4 bolts and oil cooler air duct.


7. DISCONNECT RADIATOR SIDE DEFLECTOR LH

  1. A174322
    Using a clip remover, remove the 4 clips and disconnect the side deflector.


8. REMOVE HOOD SUB-ASSEMBLY

  1. A174152
    Remove the 2 hood support bolts and disconnect the hood supports.

    CAUTION:
    Remove the hood support assembly while supporting the hood by hand.

  1. Remove the 4 bolts and hood.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

10. REMOVE FRONT FENDER APRON SEAL LH

  1. A177004
    Using a clip remover, remove the 3 clips and fender apron seal.


11. REMOVE FRONT FENDER APRON SEAL REAR LH

  1. A177005
    Using a clip remover, remove the 4 clips and fender apron seal.


12. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Using a clip remover, remove the 3 clips and fender apron seal.


13. REMOVE FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Using a clip remover, remove the 4 clips and fender apron seal.


14. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


15. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


16. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


17. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


18. REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483
  1. Remove the 4 bolts and oil pan protector assembly.


19. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A174194
    Remove the 2 bolts and No. 2 engine under cover seal.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


20. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174123E02
    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Tighten the radiator drain cock plug by hand.


21. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A174196E03
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet


22. REMOVE AIR CLEANER HOSE ASSEMBLY

  1. A243375
    Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.


23. REMOVE AIR CLEANER ASSEMBLY

  1. A174195
    Remove the 3 bolts and air cleaner.


24. REMOVE NO. 1 RADIATOR HOSE

25. REMOVE NO. 2 RADIATOR HOSE

26. REMOVE FAN SHROUD

  1. A151842
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A238869
    Disconnect the reservoir hose from the upper radiator tank.

  1. Detach the claw to open the flexible hose clamp.

  1. Remove the 2 bolts and disconnect the oil cooler tube from the fan shroud.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley.


27. REMOVE RADIATOR ASSEMBLY

  1. A174209
    Disconnect the 2 oil cooler hoses.

  1. A174155
    Remove the 4 bolts and radiator.


28. DISCONNECT FUEL MAIN AND RETURN HOSE

  1. A238245
    Remove the fuel pipe clamp.

  1. Disconnect the fuel main and return hoses (Click here).


29. DISCONNECT WIRE HARNESS AND HOSE

  1. A178804
    Disconnect the purge line hose.

  1. A239139E01
    Remove the heater hose.

  1. Disconnect the clamp and ECM connector.

    Text in Illustration 
    *A
    w/o Rear Heater
    *B
    w/ Rear Heater

    HINT:
    Refer to the following procedures to disconnect the ECM connector (Click here).

  1. A177627
    Disconnect the 4 connectors and clamp from the connector holder block.

  1. A239140
    Remove the bolt and disconnect the ground wire.

  1. A238249
    Remove the nut and disconnect the wire from the positive (+) battery cable.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Remove the bolt and disconnect the ground wire from the body.

  1. Remove the bolt and disconnect the ground wire from the bracket.

  1. Remove the nut and disconnect the wire and 2 clips from the engine room junction block.

  1. Disconnect the 2 connectors and 2 clips from the engine room junction block.

  1. Disconnect the 2 connectors and clamp.


30. DISCONNECT COOLER COMPRESSOR ASSEMBLY

  1. A178491
    Remove the 3 bolts, nut and stud bolt, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


31. DISCONNECT VANE PUMP ASSEMBLY

  1. A163289
    Remove the 2 bolts and disconnect the vane pump.


32. REMOVE GENERATOR ASSEMBLY

  1. A177892
    Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.

  1. Remove the bolt and wire harness bracket from the generator.

  1. A177893
    Remove the 3 bolts, nut and generator.

  1. Remove the stud bolt.


33. REMOVE TAILPIPE ASSEMBLY
  1. Remove the bolt, clamp and gasket.

  1. Remove the tailpipe from the 2 exhaust pipe supports.

  1. Remove the bolt and clamp, and then disconnect the tailpipe from the center exhaust pipe.


34. REMOVE CENTER EXHAUST PIPE ASSEMBLY
  1. Remove the 4 bolts.

  1. Remove the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the 2 gaskets from the front exhaust pipe and front No. 2 exhaust pipe.


35. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the bolt and disconnect the wire harness clamp bracket of the oxygen sensor from the transmission.

  1. Remove the 2 nuts, front No. 2 exhaust pipe and gasket from the exhaust manifold LH.


36. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the bolt and disconnect the wire harness clamp bracket of the oxygen sensor from the transmission.

  1. Remove the 2 nuts, front exhaust pipe and gasket from the exhaust manifold RH.


37. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A174205
    Disconnect the wire harness clamp.

  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


38. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)

39. REMOVE REAR PROPELLER SHAFT ASSEMBLY
(Click here)

40. REMOVE PROPELLER SHAFT HEAT INSULATOR

  1. A175007
    Remove the 2 bolts and heat insulator.


41. REMOVE NO. 2 MANIFOLD STAY

  1. A184508
    Remove the 3 bolts and manifold stay.


42. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A184509
    Remove the 3 bolts and heat insulator.


43. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A236969
    Remove the 8 nuts, exhaust manifold and gasket.


44. REMOVE NO. 1 MANIFOLD STAY

  1. A184511
    Remove the 3 bolts and manifold stay.


45. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A184512
    Remove the 3 bolts and heat insulator.


46. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A236970
    Remove the 8 nuts, exhaust manifold and gasket.


47. REMOVE STARTER COVER

  1. A175317
    Remove the 3 bolts and starter cover.


48. REMOVE STARTER ASSEMBLY

  1. A260965
    Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.

  1. A260966
    Remove the 2 bolts and starter.

  1. A162758
    Remove the flywheel housing side cover.


49. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)

50. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Only perform this procedure when replacement of the engine mounting insulator is necessary.

  1. C172399
    Remove the 2 bolts and front engine mounting insulator RH.

  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.


51. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

  1. A163778E02
    Using SST, hold the crankshaft.
    SST
    09213-70011  
    09330-00021  

  1. A238248
    Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor.


52. DISCONNECT OIL COOLER PIPE ASSEMBLY

  1. A174185
    Remove the 2 bolts and disconnect the oil cooler pipe.


53. REMOVE WATER PIPE AND HOSE SUB-ASSEMBLY

  1. A184532
    Remove the 2 bolts and disconnect the hose. Then remove the water pipe and hose.


54. REMOVE ENGINE ASSEMBLY

  1. A236996
    Install 2 engine hangers with 2 bolts as shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    HINT:
    Engine hanger
    12281-38150
    Bolt
    90119-14120

  1. A150148E03
    Attach an engine sling device and hang the engine with a chain block.
    Text in Illustration 
    *1
    Engine Hanger
    *2
    ENGINE
    *a
    50° or less

    NOTICE:
    When hanging the engine, make sure to hang the engine with the sling device's hanging angle at 50° or less. If not, the engine or engine hangers may be damaged.

  1. A178464E02
    Remove the 4 engine mounting insulator bolts.
    Text in Illustration 
    *A
    RH
    *B
    LH

  1. Lift the engine out from the vehicle slowly and carefully.

    NOTICE:
    1. Make sure the engine is clear of all wiring, hoses and cables.
    2. With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
    3. Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.


55. INSTALL ENGINE ON ENGINE STAND
  1. Install the engine onto an engine stand with bolts.

  1. Remove the 2 bolts and 2 engine hangers.


56. REMOVE FRONT ENGINE MOUNTING INSULATOR LH

  1. A163787
    Remove the nut and mounting insulator.


57. REMOVE FRONT ENGINE MOUNTING INSULATOR RH

  1. A174119
    Remove the nut and mounting insulator.


58. REMOVE NO. 2 FRONT ENGINE MOUNTING BRACKET LH

  1. A178524
    Remove the bolt and No. 2 front engine mounting bracket LH.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →