2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSPECTION

Inspection · Vehicles built from Sep 2011


CLEAN CYLINDER HEAD SUB-ASSEMBLY

  1. A164825
    Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.

    NOTICE:
    Be careful not to scratch the cylinder block contact surface.

  1. A164826
    Using a wire brush, remove all the carbon from the combustion chambers.

    NOTICE:
    Be careful not to damage the combustion chambers and valve seats.

  1. A164841
    Using a valve guide bushing brush and solvent, clean all the valve guide bushes.

  1. A164827
    Using a soft brush and solvent, thoroughly clean the cylinder head.


INSPECT CYLINDER HEAD SUB-ASSEMBLY

  1. A164576E01
    Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the cylinder head and cylinder block, and the cylinder head and manifolds.

    Standard Warpage:
    Item
    Specified Condition
    Cylinder block side
    0 to 0.05 mm (0 to 0.00197 in.)
    Intake manifold side
    0 to 0.08 mm (0 to 0.00315 in.)
    Exhaust manifold side
    0 to 0.08 mm (0 to 0.00315 in.)

    Maximum Warpage:
    Item
    Specified Condition
    Cylinder block side
    0.05 mm (0.00197 in.)
    Intake manifold side
    0.08 mm (0.00315 in.)
    Exhaust manifold side
    0.08 mm (0.00315 in.)

    If the warpage is more than the maximum, replace the cylinder head sub-assembly.

  1. A075610E01
    Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If there are cracks, replace the cylinder head sub-assembly.


INSPECT CYLINDER HEAD BOLT

  1. A184036E01
    Using a vernier caliper, measure the outside thread diameter of the bolt.

    Standard diameter:
    12.8 to 13.0 mm (0.504 to 0.512 in.)

    Minimum diameter:
    12.5 mm (0.492 in.)

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the smallest diameter.

    If the diameter is less than the minimum, replace the cylinder head bolt.


INSPECT NO. 2 AND NO. 3 CAMSHAFT THRUST CLEARANCE (for Intake Camshaft)
  1. Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head.

  1. Place the camshafts on the cylinder head.

  1. A164896
    Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

    NOTICE:
    Do not turn the camshafts.

  1. Install the No. 3 camshaft bearing caps.

    1. A164898E01
      Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.

    2. Temporarily install the 16 bolts.

  1. A164897E01
    Uniformly tighten the 24 bolts in several steps in the order shown in the illustration.

    Torque:
    for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for 10 mm head bolt of No. 3 camshaft bearing cap:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A164551
    Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.035 to 0.160 mm (0.00138 to 0.00630 in.)

    Maximum thrust clearance:
    0.180 mm (0.00709 in.)

    If the thrust clearance is more than the maximum, replace the camshaft.
    If necessary, replace the cylinder head sub-assembly.


INSPECT NO. 1 AND NO. 4 CAMSHAFT THRUST CLEARANCE (for Exhaust Camshaft)
  1. Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head.

  1. Place the camshafts on the cylinder head.

  1. A164958
    Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

    NOTICE:
    Do not turn the camshafts.

  1. Install the No. 3 camshaft bearing caps.

    1. A164959E01
      Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.

    2. Temporarily install the 16 bolts.

  1. A164947E01
    Uniformly tighten the 24 bolts in several steps in the order shown in the illustration.

    Torque:
    for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for 10 mm head bolt of No. 3 camshaft bearing cap:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A164550
    Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.035 to 0.160 mm (0.00138 to 0.00630 in.)

    Maximum thrust clearance:
    0.180 mm (0.00709 in.)

    If the thrust clearance is more than the maximum, replace the camshafts.
    If necessary, replace the cylinder head sub-assembly.


INSPECT CAMSHAFT

  1. A164552
    Inspect the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the runout at the center journal.

      Maximum runout:
      0.03 mm (0.00118 in.)

      If the runout is more than the maximum, replace the camshaft.

  1. A164553
    Inspect the cam lobe height.

    1. Using a micrometer, measure the cam lobe height.

      Standard Cam Lobe Height:
      Item
      Specified Condition
      No. 2 and No. 3 camshaft
      (intake)
      37.277 to 37.387 mm (1.468 to 1.472 in.)
      No. 1 and No. 4 camshaft
      (exhaust)
      38.324 to 38.434 mm (1.509 to 1.513 in.)

      Minimum Cam Lobe Height:
      Item
      Specified Condition
      No. 2 and No. 3 camshaft
      (intake)
      37.277 mm (1.468 in.)
      No. 1 and No. 4 camshaft
      (exhaust)
      38.324 mm (1.509 in.)

      If the cam lobe height is less than the minimum, replace the camshaft.

  1. A164554E02
    Inspect the camshaft journal diameter.

    1. Using a micrometer, measure the journal diameter.

      Standard Journal Diameter:
      Item
      Specified Condition
      No. 1 journal
      29.969 to 29.985 mm (1.180 to 1.181 in.)
      Other journal
      26.969 to 26.985 mm (1.0618 to 1.0624 in.)

      If the journal diameter is not as specified, check the oil clearance.


INSPECT CAMSHAFT OIL CLEARANCE
  1. Clean the camshaft bearing caps and camshaft journals.

  1. Place the camshafts on the cylinder head.

  1. A164829
    Lay a strip of Plastigage across each of the camshaft journals.

  1. A168291E01
    Temporarily install the camshaft bearing cap with the 4 bolts by hand.

    NOTICE:
    Do not turn the camshafts.

  1. Install the No. 3 camshaft bearing caps with the 16 bolts.

    1. A168292E01
      Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.

    2. Temporarily install the 16 bolts.

  1. A168293E01
    Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

    Torque:
    for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for 10 mm head bolt of No. 3 camshaft bearing cap:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A168293E02
    Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.

  1. A164830
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum oil clearance:
    0.072 mm (0.00283 in.)

    If the oil clearance is more than the maximum, replace the camshaft.
    If necessary, replace the cylinder head sub-assembly.

  1. Remove the Plastigage completely.

  1. Remove the camshafts.


INSPECT VALVE ROCKER ARM SUB-ASSEMBLY

  1. A164592
    Turn the roller by hand to check that it turns smoothly.
    If the roller does not turn smoothly, replace the valve rocker arm.


INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the adjuster free from dirt and foreign objects.
  2. Use only clean engine oil.

  1. Place the lash adjuster into a container full of new engine oil.

  1. Insert SST tip into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

    SST
    09276-75010  

  1. Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.


    A164593E01

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

    OK:
    Plunger can be pressed 3 times.

    If the plunger can still be compressed after pressing it 3 times, replace the lash adjuster with a new one.


INSPECT INNER COMPRESSION SPRING

  1. Inspect the inner compression spring deviation.

    1. A101393E02
      Using a steel square, measure the deviation of the inner compression spring.

      Maximum deviation:
      1.5 mm (0.0591 in.)

      If the deviation is more than the maximum, replace the inner compression spring.

  1. Inspect the inner compression spring free length.

    1. A101392
      Using a vernier caliper, measure the free length of the inner compression spring.

      Standard free length:
      45.9 mm (1.81 in.)

      If the free length is not as specified, replace the inner compression spring.

  1. Inspect the inner compression spring tension.

    1. EM00281E01
      Using a spring tester, measure the tension of the inner compression spring at the specified installed length.

      Installed tension:
      219 to 242 N (22 to 25 kgf, 49.2 to 54.4 lbf) at 31.0 mm (1.22 in.)

      If the installed tension is not as specified, replace the inner compression spring.


INSPECT VALVE GUIDE BUSH OIL CLEARANCE

  1. A164580
    Using a caliper gauge, measure the inside diameter of the guide bush.

    Standard bush inside diameter:
    6.01 to 6.03 mm (0.2366 to 0.2374 in.)

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard Oil Clearance:
    Item
    Specified Condition
    Intake
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)
    Exhaust
    0.035 to 0.070 mm (0.00138 to 0.00276 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    Intake
    0.120 mm (0.00472 in.)
    Exhaust
    0.130 mm (0.00512 in.)

    If the oil clearance is more than the maximum, replace the valve guide bush.


CLEAN VALVE

  1. EM00580E01
    Using a gasket scraper, chip off any carbon from the valve head.

    NOTICE:
    Be careful not to damage the valve face.

  1. Using a wire brush, thoroughly clean the valve.


INSPECT VALVE

  1. A131997
    Inspect the valve stem diameter.

    1. Using a micrometer, measure the diameter of the valve stem.

      Standard Valve Stem Diameter:
      Item
      Specified Condition
      Intake
      5.970 to 5.985 mm (0.2350 to 0.2356 in.)
      Exhaust
      5.960 to 5.975 mm (0.2346 to 0.2352 in.)

  1. A075611E05
    Inspect the valve face angle.

    1. Grind the valve enough to remove pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Standard valve face angle:
      45.5°

  1. A131998E01
    Inspect the valve head margin thickness.

    1. Using a vernier caliper, measure the valve head margin thickness.

      Standard margin thickness:
      1.0 mm (0.0394 in.)

      Minimum margin thickness:
      0.5 mm (0.0197 in.)

      If the margin thickness is less than the minimum, replace the valve.

  1. A131999E01
    Inspect the valve overall length.

    1. Using a vernier caliper, measure the overall length.

      Standard Overall Length:
      Item
      Specified Condition
      Intake
      104.4 mm (4.11 in.)
      Exhaust
      104.1 mm (4.10 in.)

      Minimum Overall Length:
      Item
      Specified Condition
      Intake
      104.1 mm (4.10 in.)
      Exhaust
      103.8 mm (4.09 in.)

      If the overall length is less than the minimum, replace the valve.

  1. EM00255E01
    Inspect the valve stem tip.

    1. Check the surface of the valve stem tip for wear.

      NOTICE:
      Do not grind the valve so it becomes shorter than the minimum overall length.

      If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.


CLEAN VALVE SEAT

  1. A164828
    Using a 45° carbide cutter, resurface the valve seats.

    NOTICE:
    Be careful not to damage the combustion chambers and valve seats.

  1. Clean the valve seats.


INSPECT INTAKE VALVE SEAT

  1. A164578E01
    Apply a light coat of Prussian blue to the valve face.

  1. Lightly press the valve face against the valve seat.

    NOTICE:
    Do not rotate the valve while pressing the valve.

  1. Check the valve face and valve seat.

    1. Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).
      If not, correct the valve seat.

    2. Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
      If not, correct the valve seat.


INSPECT EXHAUST VALVE SEAT

  1. A164579E01
    Apply a light coat of Prussian blue to the valve face.

  1. Lightly press the valve face against the valve seat.

    NOTICE:
    Do not rotate the valve while pressing the valve.

  1. Check the valve face and valve seat.

    1. Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).
      If not, correct the valve seat.

    2. Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
      If not, correct the valve seat.


VISUALLY CHECK CYLINDER BLOCK

  1. A164613
    Visually check the cylinder for vertical scratches.
    If deep scratches are present, rebore all 8 cylinders. If necessary, replace the cylinder block sub-assembly.


INSPECT CYLINDER BLOCK FOR FLATNESS

  1. A164612
    Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the cylinder head and cylinder head gaskets.

    Maximum warpage:
    0.05 mm (0.00197 in.)

    If the warpage is more than the maximum, replace the cylinder block sub-assembly.


INSPECT CONNECTING ROD BOLT

  1. A164606E01
    Using a vernier caliper, measure the tension portion diameter of the bolt.

    Standard diameter:
    8.7 to 8.8 mm (0.343 to 0.346 in.)

    Minimum diameter:
    8.5 mm (0.335 in.)

    If the diameter is less than the minimum, replace the connecting rod bolt.


INSPECT CRANKSHAFT BEARING CAP BOLT

  1. A164608E01
    Using a vernier caliper, measure the outside thread diameter of bolt A and B.
    Bolt Length 
    Item
    Specified Condition
    Bolt A
    106 mm (4.17 in.)
    Bolt B
    90.5 mm (3.56 in.)

    Measuring Area:
    Item
    Specified Condition
    Bolt A
    73 mm (2.87 in.)
    Bolt B
    63 mm (2.48 in.)

    Standard diameter:
    for bolt A:
    10.8 to 11.0 mm (0.425 to 0.433 in.)
    for bolt B:
    9.8 to 10.0 mm (0.386 to 0.394 in.)

    Minimum diameter:
    for bolt A:
    10.5 mm (0.413 in.)
    for bolt B:
    9.5 mm (0.374 in.)

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the lowest diameter.

    If the diameter is less than the minimum, replace the crankshaft bearing cap bolt.


INSPECT PISTON WITH PIN SUB-ASSEMBLY

  1. A164615E01
    Using a micrometer, measure the piston diameter at a right angle to the piston pin center line, 12 mm (0.472 in.) from the piston skirt.

    Standard piston diameter:
    85.932 to 85.966 mm (3.383 to 3.384 in.)

    Minimum piston diameter:
    85.910 mm (3.382 in.)

    If the diameter is less than the minimum, replace the piston with pin sub-assembly.


INSPECT CYLINDER BORE

  1. A164614E01
    Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.

    Standard diameter:
    86.000 to 86.013 mm (3.3858 to 3.3863 in.)

    Maximum diameter:
    86.03 mm (3.3870 in.)

    If the diameter is more than the maximum, replace the cylinder block.


INSPECT PISTON OIL CLEARANCE
  1. Subtract the piston diameter measurement from the cylinder bore diameter measurement.

    Standard oil clearance:
    0.034 to 0.081 mm (0.00134 to 0.00319 in.)

    Maximum oil clearance:
    0.091 mm (0.00358 in.)

    If the oil clearance is more than the maximum, replace all 8 pistons. If necessary, replace the cylinder block.


INSPECT PISTON PIN OIL CLEARANCE

  1. Check each mark on the piston, piston pin and connecting rod.

    A164831E02

  1. A164618
    Using a caliper gauge, measure the inside diameter of the piston pin hole.

    Standard Piston Pin Hole Inside Diameter:
    Mark
    Specified Condition
    A
    29.009 to 29.013 mm (1.1421 to 1.1422 in.)
    B
    29.013 to 29.017 mm (1.1422 to 1.1424 in.)
    C
    29.017 to 29.021 mm (1.1424 to 1.1426 in.)

  1. A132060E05
    Using a micrometer, measure the piston pin diameter.

    Standard Piston Pin Diameter:
    Mark
    Paint Color
    Specified Condition
    A
    White
    29.000 to 29.004 mm (1.1417 to 1.1419 in.)
    B
    Pink
    29.004 to 29.008 mm (1.1419 to 1.1420 in.)
    C
    Blue
    29.008 to 29.012 mm (1.1420 to 1.1422 in.)

  1. Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.

    Standard oil clearance:
    0.005 to 0.013 mm (0.000197 to 0.000512 in.)

    Maximum oil clearance:
    0.018 mm (0.000709 in.)

    If the oil clearance is more than the maximum, replace the piston and piston pin as a set.

  1. A132061
    Using a caliper gauge, measure the inside diameter of the connecting rod bush.

    Standard Bush Inside Diameter:
    Mark
    Specified Condition
    A
    29.019 to 29.023 mm (1.1425 to 1.1426 in.)
    B
    29.023 to 29.027 mm (1.1426 to 1.1428 in.)
    C
    29.027 to 29.031 mm (1.1428 to 1.1430 in.)

  1. Subtract the piston pin diameter measurement from the bush inside diameter measurement.

    Standard oil clearance:
    0.015 to 0.023 mm (0.000591 to 0.000906 in.)

    Maximum oil clearance:
    0.028 mm (0.00110 in.)

    If the oil clearance is more than the maximum, replace the connecting rod and piston with pin as a set.


INSPECT RING GROOVE CLEARANCE

  1. A164616
    Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

    Standard Ring Groove Clearance:
    Item
    Specified Condition
    No. 1 compression ring
    0.11 to 0.15 mm (0.00433 to 0.00591 in.)
    No. 2 compression ring
    0.08 to 0.12 mm (0.00315 to 0.00472 in.)
    Oil ring
    0.03 to 0.07 mm (0.00118 to 0.00276 in.)

    If the clearance is not as specified, replace the piston.


INSPECT PISTON RING END GAP

  1. A164617E01
    Insert the piston ring into the cylinder bore.

  1. Using a piston, push the piston ring a little beyond the bottom of the ring travel, 60 mm (2.36 in.) from the top of the cylinder block.

  1. A101491
    Using a feeler gauge, measure the end gap.

    Standard End Gap:
    Item
    Type of Engine
    Specified Condition
    No. 1 compression ring
    w/ EGR System
    0.22 to 0.32 mm (0.00866 to 0.0126 in.)
    w/o EGR System
    0.20 to 0.30 mm (0.00787 to 0.0118 in.)
    No. 2 compression ring
    -
    0.47 to 0.62 mm (0.0185 to 0.0244 in.)
    Oil ring
    -
    0.10 to 0.40 mm (0.00394 to 0.0157 in.)

    Maximum End Gap:
    Item
    Specified Condition
    No. 1 compression ring
    0.40 mm (0.0157 in.)
    No. 2 compression ring
    0.75 mm (0.0295 in.)
    Oil ring
    0.50 mm (0.0197 in.)

    If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, replace the cylinder block.


INSPECT CONNECTING ROD SUB-ASSEMBLY

  1. A132171
    Using a rod aligner and feeler gauge, check the connecting rod alignment.

    1. Check for bend.

      Maximum bend:
      0.07 mm (0.00276 in.) per 100 mm (3.94 in.)

      If the bend is more than the maximum, replace the connecting rod sub-assembly.

    2. A132172
      Check for twist.

      Maximum twist:
      0.15 mm (0.00591 in.) per 100 mm (3.94 in.)

      If the twist is more than the maximum, replace the connecting rod sub-assembly.


INSPECT CRANKSHAFT

  1. A164607
    Using a dial indicator and V-blocks, measure the runout as shown in the illustration.

    Maximum circle runout:
    0.04 mm (0.00157 in.)

    If the circle runout is more than the maximum, replace the crankshaft.

  1. A142818
    Using a micrometer, measure the diameter of each main journal.

    Standard diameter:
    74.982 to 75.000 mm (2.9520 to 2.9527 in.)

    If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.

  1. Check each main journal for taper and out-of-round as shown in the illustration.

    Maximum taper and out-of-round:
    0.01 mm (0.000394 in.)

    If the taper and out-of-round is more than the maximum, replace the crankshaft.

  1. A142817
    Using a micrometer, measure the diameter of each crank pin.

    Standard diameter:
    54.982 to 55.000 mm (2.1646 to 2.1653 in.)

    If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.

  1. Check each crank pin for taper and out-of-round as shown in the illustration.

    Maximum taper and out-of-round:
    0.01 mm (0.000394 in.)

    If the taper and out-of-round is more than the maximum, replace the crankshaft.


INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A164572
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.02 to 0.22 mm (0.000787 to 0.00866 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Standard thrust washer thickness:
    2.44 to 2.49 mm (0.0961 to 0.0980 in.)

    If necessary, replace the crankshaft.


INSPECT CRANKSHAFT OIL CLEARANCE

HINT:
A164803E01
Main bearings come in widths of 20.5 mm (0.807 in.) and 22.5 mm (0.886 in.).
Standard Bearing Width 
Item
Specified Condition
No. 1 and 5 journal bearings
22.5 mm (0.886 in.)
No. 2, 3 and 4 journal bearings
20.5 mm (0.807 in.)

  1. Clean each main journal and bearing.

  1. A164628
    Align the bearing claw with the claw groove of the cylinder block, and push in the 5 upper bearings.

    NOTICE:
    1. Do not apply engine oil to the bearings and the contact surfaces.
    2. Do not allow coolant to come into contact with the bearing inner surface. If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.
    3. Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

  1. A164629
    Align the bearing claw with the claw groove of the main bearing cap, and push in the 5 lower bearings.

    NOTICE:
    1. Do not apply engine oil to the bearings and the contact surfaces.
    2. Do not allow coolant to come into contact with the bearing inner surface.
      If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.

    HINT:
    A number marked on each main bearing cap indicates the installation position.

  1. A164570
    Place the crankshaft on the cylinder block.

  1. A164567E01
    Lay a strip of Plastigage across each journal.

  1. A164632E01
    Examine the front marks and numbers and install the crankshaft bearing caps to the cylinder block.

    NOTICE:
    Do not turn the crankshaft.

  1. Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.

  1. A170351E01
    Temporarily install the crankshaft bearing cap bolts labeled A or the bolts labeled B.

    HINT:
    In place of cylinder block stiffening plates, install 8 mm (0.315 in.) thick spacers to the crankshaft bearing cap bolts.

  1. Uniformly tighten the 2 crankshaft bearing cap bolts for each bearing cap in several passes to ensure a proper fit.

    NOTICE:
    Do not tap the bearing cap with a plastic-faced hammer.

  1. Remove the crankshaft bearing cap bolts and spacers.

  1. A164799E02
    Set the 2 cylinder block stiffening plates on the cylinder block.

    HINT:
    Make sure the arrows on the stiffening plates face the engine front.

  1. A178516E01
    Step 1:

    HINT:
    1. The crankshaft bearing cap bolts are tightened in 3 progressive steps.
    2. If any crankshaft bearing cap bolt is broken or deformed, replace it.


    1. Apply a light coat of engine oil to the threads and under the heads of the 20 crankshaft bearing cap bolts.

    2. Install the 20 crankshaft bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

      Torque:
      for bolt A:
      35 N*m{ 357 kgf*cm , 26 ft.*lbf }
      for bolt B:
      60 N*m{ 612 kgf*cm , 44 ft.*lbf }

  1. A164901E01
    Step 2:

    1. Mark the front side of the crankshaft bearing cap bolts A and B with paint.

    2. Tighten the crankshaft bearing cap bolts A and B 90° in the sequence shown in the illustration.

  1. A164902E01
    Step 3:

    1. Tighten the crankshaft bearing cap bolts A another 90° in the sequence shown in the illustration.

    2. A170349E02
      Check that the painted marks of bolts A are now at a 180° angle to the front.

    3. A170350E01
      Check that the painted marks of bolts B are now at a 90° angle to the front.

      NOTICE:
      Do not turn the crankshaft.

  1. A164796E02
    Step 4:

    1. Using several steps, install the 10 crankshaft bearing cap bolts uniformly in the sequence shown in the illustration.

      Torque:
      56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. Remove the crankshaft bearing caps.

    1. A164796E01
      Step 1:
      Using several steps, loosen and remove the 10 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.

    2. A164797E01
      Step 2:
      Using several steps, loosen and remove the 20 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.

  1. A164799
    Remove the 2 cylinder block stiffening plates.

  1. A164847
    Using 2 crankshaft bearing cap set bolts, pull out the 5 bearing caps.

    NOTICE:
    Take care not to damage the contact surface of the crankshaft bearing cap and cylinder block.

  1. A164568
    Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    No. 1 and 3 journals
    0.020 to 0.038 mm (0.000787 to 0.00150 in.)
    No. 2, 4 and 5 journals
    0.032 to 0.050 mm (0.00126 to 0.00197 in.)

    Maximum Clearance:
    Item
    Specified Condition
    No. 1 and 3 journals
    0.048 mm (0.00189 in.)
    No. 2, 4 and 5 journals
    0.060 mm (0.00236 in.)

    If the oil clearance is more than the maximum, use an over size bearing and correct or regrind the crankshaft so that the oil clearance is as shown in the table below.

    Oil Clearance (Use for Over Size Bearing):
    Item
    Specified Condition
    No. 1 and 3 journals
    0.021 to 0.061 mm (0.000827 to 0.00240 in.)
    No. 2, 4 and 5 journals
    0.033 to 0.073 mm (0.00130 to 0.00287 in.)

    HINT:
    Make sure to replace the upper and lower main bearings as one set.

  1. Completely remove the Plastigage.

  1. A164634E03
    If replacing a bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the appropriate bearing number. There are 7 sizes of standard bearings, marked "1", "2", "3", "4", "5", "6" and "7" accordingly.
    EXAMPLE
    Cylinder block main journal bore diameter "1" (A) + Crankshaft main journal diameter "2" (B) = Total number 3 (use bearing "3" (C))

    No. 1 to No. 5 on Cylinder Block:
    Cylinder Block (A)
    Crankshaft (B)
    Use Bearing (C)
    "1"
    "0"
    "1"
    "1"
    "2"
    "2"
    "3"
    "3"
    "4"
    "4"
    "5"
    "2"
    "0"
    "2"
    "1"
    "3"
    "2"
    "4"
    "3"
    "5"
    "4"
    "6"
    "3"
    "0"
    "3"
    "1"
    "4"
    "2"
    "5"
    "3"
    "6"
    "4"
    "7"


    Standard Cylinder Block Main Journal Bore Diameter (A):
    Item
    Mark
    Specified Condition
    No. 1 and 3 journals
    "1"
    79.000 to 79.006 mm (3.11023 to 3.11047 in.)
    "2"
    More than 79.006 to 79.012 mm (more than 3.11047 to 3.11070 in.)
    "3"
    More than 79.012 to 79.018 mm (more than 3.11070 to 3.11094 in.)
    No. 2, 4 and 5 journals
    "1"
    79.000 to 79.006 mm (3.11023 to 3.11047 in.)
    "2"
    More than 79.006 to 79.012 mm (more than 3.11047 to 3.11070 in.)
    "3"
    More than 79.012 to 79.018 mm (more than 3.11070 to 3.11094 in.)


    Standard Crankshaft Main Journal Diameter (B):
    Item
    Mark
    Specified Condition
    No. 1 and 3 journals
    "2"
    More than 74.994 to 75.000 mm (more than 2.95251 to 2.95275 in.)
    "3"
    More than 74.988 to 74.994 mm (more than 2.95228 to 2.95251 in.)
    "4"
    74.982 to 74.988 mm (2.95204 to 2.95228 in.)
    No. 2, 4 and 5 journals
    "0"
    More than 74.994 to 75.000 mm (more than 2.95251 to 2.95275 in.)
    "1"
    More than 74.988 to 74.994 mm (more than 2.95288 to 2.95251 in.)
    "2"
    74.982 to 74.988 mm (2.95204 to 2.95228 in.)


    Standard Crankshaft Bearing Center Wall Thickness (C):
    Item
    Mark
    Specified Condition
    (for Upper Bearing)
    Specified Condition
    (for Lower Bearing)
    No. 1 and 5 journal bearings
    "1"
    More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.)
    More than 1.975 to 1.978 mm (more than 0.07776 to 0.07787 in.)
    "2"
    More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.)
    More than 1.978 to 1.981 mm (more than 0.07787 to 0.07799 in.)
    "3"
    More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.)
    More than 1.981 to 1.984 mm (more than 0.07799 to 0.07811 in.)
    "4"
    More than 1.996 to 1.999 mm (more than 0.07858 to 0.07870 in.)
    More than 1.984 to 1.987 mm (more than 0.07811 to 0.07823 in.)
    "5"
    More than 1.999 to 2.002 mm (more than 0.07870 to 0.07882 in.)
    More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.)
    "6"
    More than 2.002 to 2.005 mm (more than 0.07882 to 0.07894 in.)
    More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.)
    "7"
    More than 2.005 to 2.008 mm (more than 0.07894 to 0.07905 in.)
    More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.)
    No. 2, 3 and 4 journal bearings
    "1"
    More than 1.975 to 1.978 mm (more than 0.07776 to 0.07787 in.)
    More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.)
    "2"
    More than 1.978 to 1.981 mm (more than 0.07787 to 0.07799 in.)
    More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.)
    "3"
    More than 1.981 to 1.984 mm (more than 0.07799 to 0.07811 in.)
    More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.)
    "4"
    More than 1.984 to 1.987 mm (more than 0.07811 to 0.07823 in.)
    More than 1.996 to 1.999 mm (more than 0.07858 to 0.07870 in.)
    "5"
    More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.)
    More than 1.999 to 2.002 mm (more than 0.07870 to 0.07882 in.)
    "6"
    More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.)
    More than 2.002 to 2.005 mm (more than 0.07882 to 0.07894 in.)
    "7"
    More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.)
    More than 2.005 to 2.008 mm (more than 0.07894 to 0.07905 in.)


INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A164562
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.14 to 0.54 mm (0.00551 to 0.0213 in.)

    Maximum thrust clearance:
    0.60 mm (0.0236 in.)

    If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.
    If necessary, replace the crankshaft.


INSPECT CONNECTING ROD OIL CLEARANCE
  1. Install the crankshaft bearing (Click here).

  1. Install the crankshaft (Click here).

  1. A164563E01
    Lay a strip of Plastigage across the crank pin.

  1. A164564E02
    Install the connecting rod cap so that its protrusion is facing the correct direction.

    NOTICE:
    Match the numbered connecting rod cap with the connecting rod.

  1. Apply a light coat of engine oil to the threads of the connecting rod cap bolts.

  1. A164565
    Step 1:

    HINT:
    1. The connecting rod bearing cap bolts are tightened in 2 progressive steps.
    2. If any connecting rod bearing cap bolt is broken or deformed, replace it.


    1. Install and alternately tighten the bolts of the connecting rod cap in several steps.

      Torque:
      35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. A158686E01
    Step 2:

    1. Mark the front side of each connecting rod cap bolt with paint.

    2. Tighten the bearing cap bolts in step 1 90°.

  1. Remove the 2 bolts, connecting rod cap and lower bearing.

  1. A164566
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.024 to 0.042 mm (0.000945 to 0.00165 in.)

    Maximum oil clearance:
    0.052 mm (0.00205 in.)

    If the oil clearance is more than the maximum, replace the bearings. If necessary, replace the crankshaft.

  1. Completely remove the Plastigage.

  1. A164598E02
    If replacing a bearing, replace it with one that has the same number marked on the connecting rod. There are 5 sizes of standard bearings, marked "1 ", "2", "3", "4" and "5" accordingly.
    Select the correct bearing by adding together the number marks imprinted on the connecting rod and crankshaft.
    EXAMPLE
    Connecting rod "1" (A) + Crank pin "2" (B) = Total number 3 (use bearing "3" (C))

    Standard Connecting Rod Big End Inside Diameter (A):
    Mark
    Specified Condition
    "1"
    58.000 to 58.006 mm (2.28346 to 2.28370 in.)
    "2"
    More than 58.006 to 58.012 mm (more than 2.28370 to 2.28393 in.)
    "3"
    More than 58.012 to 58.018 mm (more than 2.28393 to 2.28417 in.)

    Standard Crankshaft Pin Diameter (B):
    Mark
    Specified Condition
    "0"
    More than 54.994 to 55.000 mm (more than 2.16511 to 2.16535 in.)
    "1"
    More than 54.988 to 54.994 mm (more than 2.16488 to 2.16511 in.)
    "2"
    54.982 to 54.988 mm (2.16464 to 2.16488 in.)

    Standard Bearing Center Wall Thickness (C):
    Mark
    Specified Condition
    "1"
    More than 1.485 to 1.488 mm (more than 0.05846 to 0.05858 in.)
    "2"
    More than 1.488 to 1.491 mm (more than 0.05858 to 0.05870 in.)
    "3"
    More than 1.491 to 1.494 mm (more than 0.05870 to 0.05882 in.)
    "4"
    More than 1.494 to 1.497 mm (more than 0.05882 to 0.05894 in.)
    "5"
    More than 1.497 to 1.500 mm (more than 0.05894 to 0.05910 in.)

  1. Remove the crankshaft (Click here).

  1. Remove the crankshaft bearing.


INSPECT NO. 1 CHAIN

  1. A139523E03
    Using a spring scale, pull the No. 1 chain with a force of 147 N (15 kgf, 33.1 lbf) and measure the length of the No. 1 chain using a vernier caliper.

    Maximum chain elongation:
    143.95 mm (5.67 in.)

    NOTICE:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the No. 1 chain.


INSPECT NO. 2 CHAIN

  1. A139523E03
    Using a spring scale, pull the No. 2 chain with a force of 147 N (15 kgf, 33.1 lbf) and measure the length of the No. 2 chain using a vernier caliper.

    Maximum chain elongation:
    143.95 mm (5.67 in.)

    NOTICE:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the No. 2 chain.


INSPECT FUEL SUPPLY PUMP SHAFT SPROCKET

  1. A164844
    Wrap the No. 1 chain around the sprocket place for the No. 1 chain.

  1. Using a vernier caliper, measure the sprocket with the chain.

    Minimum gear diameter (with chain):
    101.55 mm (4.00 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and fuel supply pump shaft sprocket.

  1. A164843
    Wrap the No. 2 chain around the sprocket place for the No. 2 chain.

  1. Using a vernier caliper, measure the sprocket with the No. 2 chain.

    Minimum gear diameter (with chain):
    101.55 mm (4.00 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and fuel supply pump shaft sprocket.


INSPECT NO. 1 CAMSHAFT TIMING SPROCKET

  1. A164585
    Wrap the No. 1 chain around the sprocket.

  1. Using a vernier caliper, measure the No. 1 camshaft timing sprocket diameter with the No. 1 chain.

    Minimum gear diameter (with chain):
    134.90 mm (5.31 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and No. 1 camshaft timing sprocket.


INSPECT NO. 2 CAMSHAFT TIMING SPROCKET

  1. A164584
    Wrap the No. 2 chain around the sprocket.

  1. Using a vernier caliper, measure the No. 2 camshaft timing sprocket diameter with the No. 2 chain.

    Minimum gear diameter (with chain):
    134.90 mm (5.31 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and No. 2 camshaft timing sprocket.


INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE

  1. A164594
    Using a micrometer, measure the No. 1 idle gear shaft diameter.

    Standard idle gear shaft diameter:
    44.947 to 44.975 mm (1.770 to 1.771 in.)

  1. A164595
    Using a caliper gauge, measure the inside diameter of the idle gear.

    Standard idle gear inside diameter:
    45.000 to 45.025 mm (1.772 to 1.773 in.)

  1. Subtract the No. 1 idle gear shaft diameter measurement from the idle gear inside diameter measurement.

    Standard oil clearance:
    0.025 to 0.078 mm (0.000984 to 0.00307 in.)

    Maximum oil clearance:
    0.078 mm (0.00307 in.)

    If the thrust oil clearance is more than the maximum, replace the No. 1 idle gear shaft and idle gear as a set.


INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A164586E01
    Move the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.
    If necessary, replace the No. 1 chain tensioner assembly.


INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A164586E01
    Move the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.
    If necessary, replace the No. 2 chain tensioner assembly.


INSPECT NO. 1 CHAIN TENSIONER SLIPPER

  1. A164588E01
    Measure the worn depth of the No. 1 chain tensioner slipper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 1 chain tensioner slipper.


INSPECT NO. 2 CHAIN TENSIONER SLIPPER

  1. A164588E01
    Measure the worn depth of the No. 2 chain tensioner slipper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 2 chain tensioner slipper.


INSPECT NO. 1 CHAIN VIBRATION DAMPER

  1. A164587E01
    Measure the worn depth of the No. 1 chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 1 chain vibration damper.


INSPECT NO. 2 CHAIN VIBRATION DAMPER

  1. A164587E01
    Measure the worn depth of the No. 2 chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 2 chain vibration damper.


INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A164609
    Push the check valve with a pin to check if it is stuck.
    If stuck, replace the No. 1 oil nozzle sub-assembly.

  1. Push the check valve with a pin to check if it moves smoothly.

  1. A164610E02
    While covering A, apply air into B. Check that air does not leak through C. Perform the check again while covering B and applying air into A.
    If air leaks, clean or replace the No. 1 oil nozzle sub-assembly.

  1. A164611E02
    Push the check valve while covering A, and apply air into B. Check that air passes through C. Perform the check again while covering B, pushing the check valve and applying air into A.
    If air does not pass through C, clean or replace the No. 1 oil nozzle sub-assembly.


INSPECT NO. 1 INTAKE MANIFOLD FOR FLATNESS

  1. A164636E01
    Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the No. 1 and No. 3 intake manifold, and the No. 1 intake manifold and cylinder head.

    Maximum Warpage:
    Item
    Specified Condition
    No. 3 intake manifold
    0.10 mm (0.00394 in.)
    Cylinder head
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the No. 1 intake manifold.


INSPECT NO. 2 INTAKE MANIFOLD FOR FLATNESS

  1. A164636E01
    Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the No. 2 and No. 3 intake manifold, and the No. 2 intake manifold and cylinder head.

    Maximum Warpage:
    Item
    Specified Condition
    No. 3 intake manifold
    0.10 mm (0.00394 in.)
    Cylinder head
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the No. 2 intake manifold.


INSPECT NO. 3 INTAKE MANIFOLD FOR FLATNESS

  1. A164637E01
    Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the No. 3 and No. 1 intake manifold, the No. 3 and No. 2 intake manifold, and the No. 3 intake manifold and intake pipe.

    Maximum Warpage:
    Item
    Specified Condition
    Intake pipe
    0.10 mm (0.00394 in.)
    No. 2 and No. 3 intake manifold
    0.15 mm (0.00591 in.)

    If the warpage is more than the maximum, replace the No. 3 intake manifold.


INSPECT EXHAUST MANIFOLD FOR FLATNESS

  1. A164599E01
    Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the exhaust manifold and cylinder head.

    Maximum warpage:
    0.80 mm (0.0315 in.)

    If the warpage is more than the maximum, replace the exhaust manifold.

← DISASSEMBLY (from Jan 2012)REASSEMBLY (Sep 2011 – Dec 2011) →