2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Fuel Injector Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

Refer to DTC P0300 (Click here).

INSPECTION PROCEDURE


1. CHECK INJECTOR ASSEMBLY (POWER SOURCE)
A166988E02
  1. Disconnect the fuel injector connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    a5-2 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 2
    a1-2 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 3
    a6-2 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 4
    a2-2 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 5
    a7-2 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 6
    a3-2 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 7
    a8-2 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 8
    a4-2 - Ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 4
OK


2. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector connector.

  1. Disconnect the C45 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    a5-1 - Body ground
    Always
    10 kΩ or higher
    a5-1 - C45-86 (#10)
    Always
    Below 1 Ω
    No. 2
    a1-1 - Body ground
    Always
    10 kΩ or higher
    a1-1 - C45-109 (#20)
    Always
    Below 1 Ω
    No. 3
    a6-1 - Body ground
    Always
    10 kΩ or higher
    a6-1 - C45-85 (#30)
    Always
    Below 1 Ω
    No. 4
    a2-1 - Body ground
    Always
    10 kΩ or higher
    a2-1 - C45-108 (#40)
    Always
    Below 1 Ω
    No. 5
    a7-1 - Body ground
    Always
    10 kΩ or higher
    a7-1 - C45-84 (#50)
    Always
    Below 1 Ω
    No. 6
    a3-1 - Body ground
    Always
    10 kΩ or higher
    a3-1 - C45-107 (#60)
    Always
    Below 1 Ω
    No. 7
    a8-1 - Body ground
    Always
    10 kΩ or higher
    a8-1 - C45-83 (#70)
    Always
    Below 1 Ω
    No. 8
    a4-1 - Body ground
    Always
    10 kΩ or higher
    a4-1 - C45-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

4. INSPECT FUSE (INJ, IG2 MAIN)
A166990E04
  1. Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ fuse
    Always
    Below 1 Ω
    IG2 MAIN fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


5. INSPECT INTEGRATION NO.1 RELAY (IG2)
  1. Inspect the integration relay (IG2) (Click here).



NG
REPLACE INTEGRATION NO.1 RELAY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)


← Fuel Injector Circuit (Sep 2011 – Dec 2011)Cranking Holding Function Circuit (Sep 2011 – Dec 2011) →